SN74HC112DT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 141.690917mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Type | JK Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74HC112 |
| Function | Set(Preset) and Reset |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Output Current | 5.2mA |
| Clock Frequency | 60MHz |
| Propagation Delay | 125 ns |
| Turn On Delay Time | 13 ns |
| Family | HC/UH |
| Logic Function | AND, Flip-Flop, JK-Type |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 5.2mA 5.2mA |
| Max I(ol) | 0.004 A |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 21ns @ 6V, 50pF |
| Trigger Type | Negative Edge |
| Input Capacitance | 3pF |
| Schmitt Trigger | No |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Negative Edge |
| Height | 1.75mm |
| Length | 9.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74HC112DT Overview
The flip flop is packaged in a case of 16-SOIC (0.154, 3.90mm Width). D flip flop is embedded in the Tape & Reel (TR) package. T flip flop uses Differentialas its output configuration. There is a trigger configured with Negative Edge. Surface Mountis occupied by this electronic component. A voltage of 2V~6Vis used as the supply voltage. Temperature is set to -40°C~85°C TA. A flip flop of this type is classified as a JK Type. In terms of FPGAs, it belongs to the 74HC series. You should not exceed 60MHzin the output frequency of the device. T flip flop consumes 4μA quiescent energy. It has been determined that there have been 16 terminations. The 74HC112 family contains this object. Power is supplied from a voltage of 5V volts. There is 3pF input capacitance for this T flip flop. It belongs to the family of electronic devices known as HC/UH. This electronic part is mounted in the way of Surface Mount. 16pins are included in its design. The clock edge trigger type for this device is Negative Edge. There is a base part number FF/Latchesfor the RS flip flops. Vsup reaches its maximum value at 6V. Normally, the supply voltage (Vsup) should be above 2V. To achieve this superior flexibility, 2 circuits are used. This D flip flop is well suited for TR based on its reliable performance. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. This T flip flop features a maximum design flexibility due to its output current of 5.2mA. In order to operate, the chip has 3 output lines.
SN74HC112DT Features
Tape & Reel (TR) package
74HC series
16 pins
SN74HC112DT Applications
There are a lot of Texas Instruments SN74HC112DT Flip Flops applications.
- Event Detectors
- Asynchronous counter
- Individual Asynchronous Resets
- Common Clocks
- Digital electronics systems
- ESD protection
- Buffered Clock
- Bounce elimination switch
- Registers
- Control circuits
