SN74HC112N
| Parameters | |
|---|---|
| Supply Voltage | 5V |
| Base Part Number | 74HC112 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Channels | 2 |
| Load Capacitance | 50pF |
| Output Current | 5.2mA |
| Clock Frequency | 60MHz |
| Propagation Delay | 125 ns |
| Turn On Delay Time | 13 ns |
| Family | HC/UH |
| Logic Function | AND, Flip-Flop, JK-Type |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 5.2mA 5.2mA |
| Max I(ol) | 0.004 A |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 13ns @ 6V, 50pF |
| Trigger Type | Negative Edge |
| Input Capacitance | 3pF |
| Schmitt Trigger | No |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Negative Edge |
| Height | 5.08mm |
| Length | 19.3mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 951.693491mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74HC |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | JK Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
SN74HC112N Overview
It is packaged in the way of 16-DIP (0.300, 7.62mm). There is an embedded version in the package Tube. T flip flop is configured with an output of Differential. In the configuration of the trigger, Negative Edgeis used. Through Holemounts this electrical part. The JK flip flop operates at 2V~6Vvolts. In this case, the operating temperature is -40°C~85°C TA. The type of this D latch is JK Type. JK flip flop belongs to the 74HCseries of FPGAs. Its output frequency should not exceed 60MHz Hz. This process consumes 4μA quiescents. It has been determined that there have been 16 terminations. D latch belongs to the 74HC112 family. Power is provided by a 5V supply. Its input capacitance is 3pF farads. HC/UHis the family of this D flip flop. It is mounted by the way of Through Hole. This board has 16 pins. This device has the clock edge trigger type of Negative Edge. The part you are looking for is included in FF/Latches. The maximal supply voltage (Vsup) reaches 6V. Keeping the supply voltage (Vsup) above 2V is necessary for normal operation. In order to ensure high efficiency, the supply voltage should remain at 5V. In addition to its maximum design flexibility, the output current of the T flip flop is 5.2mA. In order to operate, the chip has 3 output lines. There are 2 channels available.
SN74HC112N Features
Tube package
74HC series
16 pins
SN74HC112N Applications
There are a lot of Texas Instruments SN74HC112N Flip Flops applications.
- Functionally equivalent to the MC10/100EL29
- ESCC
- Parallel data storage
- Reduced system switching noise
- Safety Clamp
- Pattern generators
- Single Up Count-Control Line
- Storage Registers
- Shift Registers
- Digital electronics systems
