SN74HC158PWT
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Weight | 61.887009mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Discontinued |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Termination | SMD/SMT |
| Type | Multiplexer |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74HC158 |
| Pin Count | 16 |
| Number of Outputs | 1 |
| Circuit | 4 x 2:1 |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Load Capacitance | 50pF |
| Number of Bits | 4 |
| Propagation Delay | 33 ns |
| Family | HC/UH |
| Current - Output High, Low | 7.8mA 7.8mA |
| Supply Type | Single |
| Output Polarity | INVERTED |
| Max I(ol) | 0.006 A |
| Number of Input Lines | 2 |
| Voltage Supply Source | Single Supply |
| Independent Circuits | 1 |
| Length | 5mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
SN74HC158PWT Overview
Due to the fact that it is provided in the 16-TSSOP (0.173, 4.40mm Width), digital switch allows the board to be compacted.As a result, it is packaged in a way that is referred to as Tape & Reel (TR).As far as mounting is concerned, digital switch ic uses Surface Mount.For the analog part of the multiplexers, an IC Multiplexer is used.If the operating temperature is maintained at -40°C~85°C, turn signal switch will not be susceptible to external factors.Designers have greater flexibility using digital controlled switch when it works with 2V~6V voltage.The multiplexers from 74HC series can be used for a wide range of applications.Its basic configuration includes terminations in the 16 range.The base part number is 74HC158, which is also useful when looking up signal switch's related components.In multiplexer's system, 5V is the voltage supplied.Signal switch has 16 component pins.Conductors terminate at GULL WING in this design.There is a supply type of Single employed as part of this supply.With 16 pins, it is configured.As you can see, it is mounted in the direction of Surface Mount.The logic switch belongs to the family of HC/UH.There are 4 bits signal multiplexer provides.It is recommended that the minimum supply voltage (Vsup) be kept at 2V so that unnecessary failures can be prevented.It is advisable to keep the maximum supply voltage (Vsup) at 6V so as to avoid some unnecessary failures.The turn signal switch contains 1 outputs designed to operate.According to TAPE AND REEL, the switches is packaged.In order to accept voltage levels, the multiplexers have input lines 2 on the board.
SN74HC158PWT Features
Supplied in the 16-TSSOP (0.173, 4.40mm Width) package
Adopting a supply type of Single
2 input lines
SN74HC158PWT Applications
There are a lot of Texas Instruments SN74HC158PWT Signal Switches / Multiplexers / Decoders applications.
- Used to connect a single source to multiple destinations
- Automatic health monitoring systems
- Small scale TV wall
- Speed control of medern motors
- LVDS
- Injectors
- Home automation system
- Enabling block of memory depending on address in memory chips
- Data bus control
- Combinational circuit
