SN74HC174DRE4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 16 |
| Weight | 141.690917mg |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 16 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Frequency | 50MHz |
| Pin Count | 16 |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Temperature Grade | INDUSTRIAL |
| Number of Circuits | 7 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Load Capacitance | 50pF |
| Current - Output | 5.2mA |
| Number of Bits | 6 |
| Propagation Delay | 160 ns |
| Turn On Delay Time | 14 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Logic IC Type | D FLIP-FLOP |
| Max I(ol) | 0.004 A |
| High Level Output Current | -5.2mA |
| Low Level Output Current | 5.2mA |
| Number of Input Lines | 3 |
| Number of Output Lines | 1 |
| fmax-Min | 29 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Length | 9.9mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74HC174DRE4 Overview
SOICis the packaging method. As part of the package Tape & Reel (TR), it is embedded. Terminations are 16. Power is provided by a 5V supply. HC/UHis the family of this D flip flop. There is an electronic component mounted in the way of Surface Mount. As you can see from the design, it has pins with 16. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. This device is part of the FF/Latchesbase part number family. The flip flop is designed with 6bits. The superior flexibility is achieved through the use of 7 circuits. As a result of its reliable performance, this T flip flop is suitable for TAPE AND REEL. It is recommended that the supply voltage be kept at 5Vto maximize efficiency. In order for the chip to function, it has 1output lines. There are 3 input Lines, which consist of an electronic circuit connected between the ac mains and the rectifier input stage of the switching power supply. The high level output current is set to -5.2mA. It is set to 5.2mAfor low level output current. If the operating temperature is lower than 85°C, it is recommended. It should be higher than -40°Cwhen the system is operating. In order for it to operate, a supply voltage of 2Vis required. It is capable of supporting a maximum supply voltage of 6V. A frequency of 50MHzcan be achieved. The logic IC it adopts is D FLIP-FLOP. A total of 1 functions are provided by this T flip flop. This device is equipped with a pin count of 16. It offers maximum design flexibility with its output current of 5.2mA.
SN74HC174DRE4 Features
Tape & Reel (TR) package
16 pins
6 Bits
1 Functions
16 pin count
SN74HC174DRE4 Applications
There are a lot of Texas Instruments SN74HC174DRE4 Flip Flops applications.
- Frequency Dividers
- Computers
- Consumer
- Registers
- Event Detectors
- Communications
- Bus hold
- Single Down Count-Control Line
- Shift registers
- Buffered Clock
