SN74HC175DR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 141.690917mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74HC175 |
| Function | Master Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 4 |
| Load Capacitance | 50pF |
| Output Current | 25mA |
| Number of Bits | 4 |
| Clock Frequency | 60MHz |
| Propagation Delay | 150 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 13 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 5.2mA 5.2mA |
| Max Propagation Delay @ V, Max CL | 26ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Power Supply Current-Max (ICC) | 0.08mA |
| Number of Input Lines | 3 |
| Number of Output Lines | 2 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.75mm |
| Length | 9.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74HC175DR Overview
16-SOIC (0.154, 3.90mm Width)is the way it is packaged. There is an embedded version in the package Cut Tape (CT). T flip flop is configured with an output of Differential. The trigger configured with it uses Positive Edge. Surface Mountmounts this electrical part. A voltage of 2V~6Vis used as the supply voltage. In the operating environment, the temperature is -40°C~85°C TA. It is an electronic flip flop with the type D-Type. FPGAs belonging to the 74HCseries contain this type of chip. This D flip flop should not have a frequency greater than 60MHz. In total, there are 1 elements. 16terminations have occurred. D latch belongs to the 74HC175 family. It is powered from a supply voltage of 5V. Its input capacitance is 3pF farads. The electronic device belongs to the HC/UHfamily. The electronic part is mounted in the way of Surface Mount. Basically, it is designed with a set of 16 pins. The clock edge trigger type for this device is Positive Edge. The RS flip flops belongs to FF/Latches base part number. It is designed with a number of bits of 4. As soon as 6Vis reached, Vsup reaches its maximum value. For normal operation, the supply voltage (Vsup) should be kept above 2V. The superior flexibility of this circuit is achieved by using 4 circuits. In light of its reliable performance, this T flip flop is well suited for TR. For high efficiency, the supply voltage should be kept at 5V. In addition to its maximum design flexibility, the output current of the T flip flop is 25mA. To operate, the chip has a total of 2 output lines. There are 3 input Lines, which consist of an electronic circuit connected between the ac mains and the rectifier input stage of the switching power supply. As a result, it consumes 8μA of quiescent current without being affected by external factors.
SN74HC175DR Features
Cut Tape (CT) package
74HC series
16 pins
4 Bits
SN74HC175DR Applications
There are a lot of Texas Instruments SN74HC175DR Flip Flops applications.
- ESD performance
- Functionally equivalent to the MC10/100EL29
- Frequency division
- Consumer
- Latch-up performance
- EMI reduction circuitry
- Balanced Propagation Delays
- Reduced system switching noise
- Computers
- Synchronous counter
