SN74HC175DT
| Parameters | |
|---|---|
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Discontinued |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74HC175 |
| Function | Master Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 4 |
| Load Capacitance | 50pF |
| Output Current | 5.2mA |
| Number of Bits | 4 |
| Clock Frequency | 60MHz |
| Propagation Delay | 150 ns |
| Turn On Delay Time | 13 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 5.2mA 5.2mA |
| Max Propagation Delay @ V, Max CL | 26ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Output Lines | 2 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 141.690917mg |
SN74HC175DT Overview
In the form of 16-SOIC (0.154, 3.90mm Width), it has been packaged. A package named Tape & Reel (TR)includes it. T flip flop is configured with an output of Differential. The trigger configured with it uses Positive Edge. Surface Mountmounts this electrical part. The JK flip flop operates at a voltage of 2V~6V. It is operating at -40°C~85°C TA. D-Typedescribes this flip flop. In terms of FPGAs, it belongs to the 74HC series. You should not exceed 60MHzin its output frequency. D latch consists of 1 elements. It consumes 8μA of quiescent current without being affected by external factors. There have been 16 terminations. If you search by 74HC175, you will find similar parts. Power is supplied from a voltage of 5V volts. A 3pFfarad input capacitance is provided by this T flip flop. It is a member of the HC/UHfamily of D flip flop. This electronic part is mounted in the way of Surface Mount. There are 16pins on it. This device has Positive Edgeas its clock edge trigger type. The part is included in FF/Latches. The flip flop is designed with 4bits. 6Vis the maximum supply voltage (Vsup). Normal operation requires a supply voltage (Vsup) above 2V. Using 4 circuits, it is highly flexible. This D flip flop is well suited for TAPE AND REEL based on its reliable performance. For high efficiency, the supply voltage should be set to 5V. The output current of 5.2mA makes it feature maximum design flexibility. It operates with 2 output lines.
SN74HC175DT Features
Tape & Reel (TR) package
74HC series
16 pins
4 Bits
SN74HC175DT Applications
There are a lot of Texas Instruments SN74HC175DT Flip Flops applications.
- Parallel data storage
- High Performance Logic for test systems
- Dynamic threshold performance
- Reduced system switching noise
- Single Up Count-Control Line
- ESD performance
- Computers
- Data Synchronizers
- Registers
- Modulo – n – counter
