SN74HC273DBR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Weight | 156.687814mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Additional Feature | DUMMY VAL |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74HC273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Output Current | 5.2mA |
| Number of Bits | 8 |
| Clock Frequency | 60MHz |
| Propagation Delay | 200 ns |
| Turn On Delay Time | 13 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 5.2mA 5.2mA |
| Max Propagation Delay @ V, Max CL | 27ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 2 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2mm |
| Length | 7.2mm |
| Width | 5.3mm |
| Thickness | 1.95mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74HC273DBR Overview
The item is packaged in 20-SSOP (0.209, 5.30mm Width)cases. D flip flop is embedded in the Cut Tape (CT) package. As configured, the output uses Non-Inverted. This trigger uses the value Positive Edge. There is an electric part mounted in the way of Surface Mount. It operates with a supply voltage of 2V~6V. Temperature is set to -40°C~85°C TA. This logic flip flop is classified as type D-Type. The 74HCseries comprises this type of FPGA. Its output frequency should not exceed 60MHz. The list contains 1 elements. There is a consumption of 8μAof quiescent energy. 20terminations have occurred. It is a member of the 74HC273 family. A voltage of 5V is used to power it. This T flip flop has a capacitance of 3pF farads at the input. An electronic device belonging to the family HC/UHcan be found here. It is mounted by the way of Surface Mount. Basically, it is designed with a set of 20 pins. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. The RS flip flops belongs to FF/Latches base part number. It is designed with 8bits. Vsup reaches its maximum value at 6V. Normal operation requires a supply voltage (Vsup) above 2V. Due to its superior flexibility, it uses 8 circuits. In view of its reliability, this D flip flop is a good fit for TR. High efficiency requires the supply voltage to be maintained at 5V. As a result of its output current of 5.2mA, it is very flexible in terms of design. Currently, there are 2 lines of input. Additionally, there are DUMMY VAL on the electronic flip flop that can be referred to.
SN74HC273DBR Features
Cut Tape (CT) package
74HC series
20 pins
8 Bits
SN74HC273DBR Applications
There are a lot of Texas Instruments SN74HC273DBR Flip Flops applications.
- Memory
- Data storage
- Frequency Divider circuits
- 2 – Bit synchronous counter
- Matched Rise and Fall
- Buffer registers
- Patented noise
- Count Modes
- Test & Measurement
- Communications
