SN74HC273DBRG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | SSOP |
| Number of Pins | 20 |
| Weight | 156.687814mg |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | DUMMY VAL |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Frequency | 60MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Load Capacitance | 50pF |
| Current - Output | 5.2mA |
| Propagation Delay | 200 ns |
| Turn On Delay Time | 13 ns |
| Family | HC/UH |
| Logic Function | D-Type |
| Logic IC Type | D FLIP-FLOP |
| Max I(ol) | 0.004 A |
| Number of Bits per Element | 8 |
| High Level Output Current | -5.2mA |
| Low Level Output Current | 5.2mA |
| fmax-Min | 25 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.95mm |
| Length | 7.5mm |
| Width | 5.6mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74HC273DBRG4 Overview
The flip flop is packaged in SSOP. The list contains 1 elements. Currently, there are 20 terminations. A voltage of 5V is used to power it. It is a member of the HC/UHfamily of D flip flop. The electronic part is mounted in the way of Surface Mount. The 20pins are designed into the board. It has a clock edge trigger type of Positive Edge. The part you are looking for is included in FF/Latches. Due to its reliability, this T flip flop is well suited for TAPE AND REEL. In order to ensure high efficiency, the supply voltage should remain at 5V. Additionally, it is characterized by DUMMY VAL. A -5.2mAis set for the high level output current. The low level output current is set to 5.2mA. A temperature below 85°Cshould be used for operation. Operating temperatures should be above -40°C. A minimum supply voltage of 2V is required for these RS flip flops to operate. A maximum voltage of 6V can be provided by it. It is possible to obtain a frequency of 60MHz. In this case, it uses a D FLIP-FLOP logic IC. It has 1 functions. With 20 pins, it is equipped with a low power consumption. This flip flop features a maximum design flexibility due to its output current of 5.2mA.
SN74HC273DBRG4 Features
20 pins
1 Functions
20 pin count
SN74HC273DBRG4 Applications
There are a lot of Texas Instruments SN74HC273DBRG4 Flip Flops applications.
- Balanced Propagation Delays
- Safety Clamp
- ESCC
- Computers
- Single Down Count-Control Line
- Shift registers
- Event Detectors
- Bus hold
- Common Clocks
- Differential Individual
