SN74HC273PWR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Additional Feature | DUMMY VAL |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74HC273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Output Current | 25mA |
| Number of Bits | 8 |
| Clock Frequency | 60MHz |
| Propagation Delay | 200 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 13 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 5.2mA 5.2mA |
| Max Propagation Delay @ V, Max CL | 27ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 2 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.2mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74HC273PWR Overview
20-TSSOP (0.173, 4.40mm Width)is the way it is packaged. It is contained within the Cut Tape (CT)package. This output is configured with Non-Inverted. The trigger configured with it uses Positive Edge. Surface Mountmounts this electrical part. The JK flip flop operates at a voltage of 2V~6V. In the operating environment, the temperature is -40°C~85°C TA. The type of this D latch is D-Type. In this case, it is a type of FPGA belonging to the 74HC series. You should not exceed 60MHzin the output frequency of the device. The list contains 1 elements. There are 20 terminations,If you search by 74HC273, you will find similar parts. The power supply voltage is 5V. The input capacitance of this JK flip flopis 3pF farads. A device of this type belongs to the family of HC/UH. This electronic part is mounted in the way of Surface Mount. The 20pins are designed into the board. A Positive Edgeclock edge trigger is used in this device. There is a FF/Latchesbase part number assigned to the RS flip flops. It is designed with a number of bits of 8. In this case, the maximum supply voltage (Vsup) reaches 6V. It is imperative that the supply voltage (Vsup) is maintained above 2Vin order to ensure normal operation. The superior flexibility is achieved through the use of 8 circuits. As a result of its reliability, this D flip flop is ideally suited for TR. If high efficiency is desired, the supply voltage should be kept at 5V. It offers maximum design flexibility with its output current of 25mA. Currently, there are 2 lines of input. As a result, it consumes 8μA of quiescent current without being affected by external factors. In addition, you can refer to the additinal DUMMY VAL of the D latch.
SN74HC273PWR Features
Cut Tape (CT) package
74HC series
20 pins
8 Bits
SN74HC273PWR Applications
There are a lot of Texas Instruments SN74HC273PWR Flip Flops applications.
- Data transfer
- Guaranteed simultaneous switching noise level
- Event Detectors
- ESD protection
- Load Control
- Bounce elimination switch
- Control circuits
- High Performance Logic for test systems
- Storage Registers
- Individual Asynchronous Resets
