SN74HC273QPWRQ1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | Automotive, AEC-Q100, 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74HC273 |
| Function | Master Reset |
| Qualification Status | Not Qualified |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Bits | 8 |
| Clock Frequency | 60MHz |
| Propagation Delay | 27 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 13 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 5.2mA 5.2mA |
| Max Propagation Delay @ V, Max CL | 27ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 2 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.2mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74HC273QPWRQ1 Overview
As a result, it is packaged as 20-TSSOP (0.173, 4.40mm Width). It is included in the package Tape & Reel (TR). Non-Invertedis the output configured for it. In the configuration of the trigger, Positive Edgeis used. There is an electric part mounted in the way of Surface Mount. A voltage of 2V~6Vis required for its operation. A temperature of -40°C~125°C TAis used in the operation. The type of this D latch is D-Type. The FPGA belongs to the Automotive, AEC-Q100, 74HC series. In order for it to function properly, its output frequency should not exceed 60MHz. A total of 1elements are contained within it. Currently, there are 20 terminations. The object belongs to the 74HC273 family. A voltage of 5V is used as the power supply for this D latch. This T flip flop has a capacitance of 3pF farads at the input. Electronic devices of this type belong to the HC/UHfamily. There is an electronic component mounted in the way of Surface Mount. The 20pins are designed into the board. The clock edge trigger type for this device is Positive Edge. This RS flip flops is a part number FF/Latches. There are 8bits in this flip flop. As soon as 6Vis reached, Vsup reaches its maximum value. A normal operating voltage (Vsup) should remain above 2V. Due to its superior flexibility, it uses 8 circuits. In view of its reliability, this D flip flop is a good fit for TR. High efficiency requires the supply voltage to be maintained at 5V. There are 2 input Lines, which consist of an electronic circuit connected between the ac mains and the rectifier input stage of the switching power supply. 8μAquiescent current consumed.
SN74HC273QPWRQ1 Features
Tape & Reel (TR) package
Automotive, AEC-Q100, 74HC series
20 pins
8 Bits
SN74HC273QPWRQ1 Applications
There are a lot of Texas Instruments SN74HC273QPWRQ1 Flip Flops applications.
- Single Down Count-Control Line
- Control circuits
- ESCC
- Convert a momentary switch to a toggle switch
- Memory
- Parallel data storage
- Modulo – n – counter
- Storage Registers
- ESD performance
- Consumer
