Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 1 day ago) |
Contact Plating |
Gold |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
20-SOIC (0.295, 7.50mm Width) |
Number of Pins |
20 |
Weight |
500.709277mg |
Operating Temperature |
-40°C~85°C |
Packaging |
Tube |
Series |
74HC |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
20 |
Subcategory |
FF/Latches |
Technology |
CMOS |
Voltage - Supply |
2V~6V |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
5V |
Base Part Number |
74HC373 |
Pin Count |
20 |
Number of Outputs |
8 |
Output Type |
Tri-State |
Operating Supply Voltage |
5V |
Circuit |
8:8 |
Polarity |
Non-Inverting |
Supply Voltage-Max (Vsup) |
6V |
Power Supplies |
2/6V |
Supply Voltage-Min (Vsup) |
2V |
Number of Ports |
2 |
Nominal Supply Current |
1μA |
Output Current |
7.8mA |
Number of Bits |
8 |
Propagation Delay |
19 ns |
Quiescent Current |
8μA |
Turn On Delay Time |
15 ns |
Family |
HC/UH |
Logic Function |
D-Type, Latch |
Output Characteristics |
3-STATE |
Current - Output High, Low |
7.8mA 7.8mA |
Logic Type |
D-Type Transparent Latch |
Control Type |
ENABLE LOW |
Number of Input Lines |
9 |
Independent Circuits |
1 |
Count Direction |
UNIDIRECTIONAL |
Height |
2.65mm |
Length |
12.8mm |
Width |
7.5mm |
Thickness |
2.35mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
SN74HC373DW Overview
The 20-SOIC (0.295, 7.50mm Width) package contains it. This package has the format of Tube. It uses Tri-State as the output. This electrical device has a logic type of D-Type Transparent Latch. Mounting this electronic component follows the Surface Mount method. In order for it to operate, it needs a supply voltage of 2V~6V. The operating temperature is -40°C~85°C. 74HC is the series number of this FPGA. With this electronic part, there are 8 bits. A device with this design has 20 terminations. The family it belongs to is 74HC373. In order to operate it, the supply voltage must be 5V. With 20 pins, it is equipped. It is part of the family of electronic devices called HC/UH. It is designed with 20 pins. A Surface Mount mounting method has been used for this electronic part. This device has a total of 2 ports. The part is in the FF/Latches subcategory. It reaches a maximum supply voltage (Vsup) of 6V. A total of 2/6V power supplies are required for it to operate. (Vsup) should be greater than 2V. An electronic circuit can be found on 9 input lines. It features maximum flexibility in design due to 7.8mA output current. High efficiency requires maintaining the supply voltage at 5V. It consumes 8μA of quiescent current without being affected by outside factors.
SN74HC373DW Features
20-SOIC (0.295, 7.50mm Width) package
74HC series
8 Bits
74HC373 family
20 pin count
20 pins
2/6V power supplies
SN74HC373DW Applications
There are a lot of Texas Instruments SN74HC373DW Latches applications.
- Address register
- Digital bus buffer
- Parallel Input
- Pattern Generators
- Synchronous frequency dividers
- Counter timers
- Clocks
- Avionics
- Timers
- Serial Input