Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 5 days ago) |
Contact Plating |
Gold |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
20-TSSOP (0.173, 4.40mm Width) |
Number of Pins |
20 |
Weight |
76.997305mg |
Operating Temperature |
-40°C~85°C |
Packaging |
Cut Tape (CT) |
Series |
74HC |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
20 |
ECCN Code |
EAR99 |
Subcategory |
FF/Latches |
Packing Method |
TR |
Technology |
CMOS |
Voltage - Supply |
2V~6V |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
5V |
Terminal Pitch |
0.65mm |
Base Part Number |
74HC373 |
Pin Count |
20 |
Output Type |
Tri-State |
Operating Supply Voltage |
5V |
Circuit |
8:8 |
Polarity |
Non-Inverting |
Supply Voltage-Max (Vsup) |
6V |
Power Supplies |
2/6V |
Supply Voltage-Min (Vsup) |
2V |
Number of Circuits |
8 |
Load Capacitance |
50pF |
Number of Ports |
2 |
Output Current |
7.8mA |
Number of Bits |
8 |
Propagation Delay |
43 ns |
Quiescent Current |
8μA |
Turn On Delay Time |
15 ns |
Family |
HC/UH |
Logic Function |
D-Type, Latch |
Current - Output High, Low |
7.8mA 7.8mA |
Logic Type |
D-Type Transparent Latch |
Control Type |
ENABLE LOW |
Number of Input Lines |
3 |
Independent Circuits |
1 |
Count Direction |
UNIDIRECTIONAL |
Height |
1.2mm |
Length |
6.5mm |
Width |
4.4mm |
Thickness |
1mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
SN74HC373PWR Overview
In the 20-TSSOP (0.173, 4.40mm Width) package, it can be found as an embedded module. A package of Cut Tape (CT) has been used. It uses the output configuration Tri-State. There is a logic type of D-Type Transparent Latch for this electrical device. Mounting this electronic component follows the Surface Mount method. The voltage supply is 2V~6V. A temperature of -40°C~85°C is set as the operating temperature. It is a type of FPGA belonging to the 74HC series. It is designed with 8 bits. This device has 20 terminations. It belongs to 74HC373 family. In order to operate it, the supply voltage must be 5V. The device is equipped with 20 pins. There is a device in this electronic family called HC/UH. The pin configuration of the device is 20. Surface Mount is the method used for mounting this electronic part. In this device, there is a total of 2 ports available for use. There is a subcategory of FF/Latches for this part. 6V is the maximum voltage (Vsup) that can be supplied. There are 2/6V power supplies required for this machine to operate. (Vsup) should be greater than 2V. Input Lines consist of electronic circuits, and there are 3. As a result of its reliable performance, it is well suited for TR. With 7.8mA, maximum design flexibility is ensured. Optimal efficiency requires 5V as the supply voltage. As far as external factors are concerned, it consumes 8μA of quiescent current without getting affected by them. It achieves superior flexibility by using 8 circuits.
SN74HC373PWR Features
20-TSSOP (0.173, 4.40mm Width) package
74HC series
8 Bits
74HC373 family
20 pin count
20 pins
2/6V power supplies
SN74HC373PWR Applications
There are a lot of Texas Instruments SN74HC373PWR Latches applications.
- Automotive ADAS
- Synchronous frequency dividers
- Parallel data storage
- Counters
- Up-Down Johnson
- Stacked or Push-Down Registers
- Multi-line decoders
- Sample and hold register
- Instrumentation
- A/D and D/A conversion