SN74HC374PWRG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | TSSOP |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Frequency | 70MHz |
| Pin Count | 20 |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Current - Output | 7.8mA |
| Propagation Delay | 230 ns |
| Turn On Delay Time | 15 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Output Characteristics | 3-STATE |
| Logic IC Type | BUS DRIVER |
| Max I(ol) | 0.006 A |
| Number of Bits per Element | 8 |
| High Level Output Current | -7.8mA |
| Low Level Output Current | 7.8mA |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.15mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74HC374PWRG4 Overview
The flip flop is packaged in a case of TSSOP. A total of 1 elements are present. There have been 20 terminations. Power is supplied from a voltage of 5V volts. In terms of electronic devices, this device belongs to the HC/UHfamily of devices. Surface Mount mounts this electronic component. There are 20pins on it. In this device, the clock edge trigger type is Positive Edge. This part is included in FF/Latches. As a result of its reliability, this D flip flop is ideally suited for TR. The flip flop has 2embedded ports. A high level of efficiency can be achieved by maintaining the supply voltage at 5V. There is -7.8mA output current at the high level. It is set to 7.8mAfor low level output current. Temperatures below 85°Care ideal for operating. In order for the system to operate properly, the temperature should be higher than -40°C. It operates with the minimal supply voltage of 2V. 6Vis its maximum supply voltage. This can be achieved at a frequency of 70MHz. There is a logic IC BUS DRIVER used in the D flip flop. There are 1 functions associated with the JK flip flop. 20pins are available on this JK flip flop. 7.8mA provides maximum design flexibility due to its output current.
SN74HC374PWRG4 Features
20 pins
1 Functions
20 pin count
SN74HC374PWRG4 Applications
There are a lot of Texas Instruments SN74HC374PWRG4 Flip Flops applications.
- Event Detectors
- Load Control
- Circuit Design
- 2 – Bit synchronous counter
- Consumer
- Differential Individual
- Pattern generators
- CMOS Process
- Buffer registers
- Asynchronous counter
