SN74HC4066DBR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 14 |
| Weight | 121.789551mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 30Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 4.5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74HC4066 |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Number of Channels | 4 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 2μA |
| Max Supply Current | 2μA |
| Throw Configuration | SPST |
| Propagation Delay | 15 ns |
| Turn On Delay Time | 38 ns |
| Supply Type | Single |
| Bandwidth | 30MHz |
| Turn-Off Delay Time | 43 ns |
| On-State Resistance (Max) | 30Ohm Typ |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 42 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 0.5pF 9pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 31ns, 34ns |
| Crosstalk | -45dB @ 1MHz |
| Switching | MAKE-BEFORE-BREAK |
| Switch-on Time-Max | 36ns |
| Voltage - Supply, Single (V+) | 2V~6V |
| Normal Position | NO |
| Height | 2mm |
| Length | 6.2mm |
| Width | 5.3mm |
| Thickness | 1.95mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74HC4066DBR Overview
The electronic component is convenient to ship overseas because it is packed in a 14-SSOP (0.209, 5.30mm Width). To ensure high reliability, a new packaging method Cut Tape (CT) is used. There is an analog multiplexer mounted in position Surface Mount. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operating temperature extended to -40°C~85°C TA. There are 14 terminations totally. The electronic part delivers high-quality output through its 4 channels. It is safe to turn on and run the electronic component with a 4.5V voltage supply. The electronic part body is injected with 14 pins. A SPST - NO switching circuit is used for these analog switches. Using the 74HC4066 search parameter, you can discover variants of the switch. In this multiplexer, the internal resistance is 30Ohm. Datasheets for functions of 14 pins are available. Theswitch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 6V in normal situations. A cost-effective Single supply type analogue multiplexer. The lowest voltage the electronic part should receive is 2V. In order to operate this switch device, it would need a current of 2μA. An analogue multiplexer drains from a single voltage supply at 2V~6V. Putting voltage greater than 2μA on the multiplexer may cause damage. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. It can operate from 5V operating voltages. 30MHz-bandwidths can be used to transfer data between multiplexers.
SN74HC4066DBR Features
4 Channels
Switch Circuit: SPST - NO
2μA Supply Current
Bandwidth: 30MHz
SN74HC4066DBR Applications
There are a lot of Texas Instruments SN74HC4066DBR Analog Switches & Multiplexers ICs applications.
- ATM
- Avionics and Military Systems
- Medical
- Central office
- DSLAMs
- Private Branch Exchange (PBX)
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Data switching
- Transmit
- Wireless Local Loop
