SN74HC4066DRE4
| Parameters | |
|---|---|
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 4.5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74HC4066 |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Qualification Status | Not Qualified |
| Number of Channels | 4 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 2μA |
| Max Supply Current | 2μA |
| Throw Configuration | SPST |
| Propagation Delay | 15 ns |
| Turn On Delay Time | 180 ns |
| Supply Type | Single |
| Bandwidth | 30MHz |
| Turn-Off Delay Time | 200 ns |
| On-State Resistance (Max) | 30Ohm Typ |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 42 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 0.5pF 9pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 31ns, 34ns |
| Crosstalk | -45dB @ 1MHz |
| Switching | MAKE-BEFORE-BREAK |
| Switch-on Time-Max | 36ns |
| Voltage - Supply, Single (V+) | 2V~6V |
| Normal Position | NO |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Weight | 129.387224mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 30Ohm |
SN74HC4066DRE4 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 14-SOIC (0.154, 3.90mm Width). High reliability is provided by advanced packaging method Tape & Reel (TR). In Surface Mount, you'll find this switch device. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Temperatures around -40°C~85°C TA are extended for operation. A total of 14 terminations have been recorded. Due to its 4 channels, the electrical component produces high-quality output. A 4.5V voltage supply should turn on and run the electronic component. The electronic part body is injected with 14 pins. The analog switch ics are built using SPST - NO switching circuits. Try searching for the analog switch ic with 74HC4066 if you are looking for variants. Analog switches have 30Ohm internal resistance. To find out what the functions of 14 pins are, please refer to their datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. A voltage higher than 6V should not normally be supplied to the switches. Analog switch ics with Single supply type are cost-effective. The lowest voltage the electronic part should receive is 2V. This multiplexer would work with 2μA current. Draining from a single voltage supply, this analog switch requires a voltage of 2V~6V. A digital multiplexer may suffer damage if voltage is applied above 2μA. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. The transfer of data can be performed over 30MHz bandwidths.
SN74HC4066DRE4 Features
4 Channels
Switch Circuit: SPST - NO
2μA Supply Current
Bandwidth: 30MHz
SN74HC4066DRE4 Applications
There are a lot of Texas Instruments SN74HC4066DRE4 Analog Switches & Multiplexers ICs applications.
- Microwave transmission systems
- Medical Instrumentation
- Access Concentrators
- 65 V DACs
- Imaging
- Digital Cross-Connects
- Data Acquisition Systems
- Communication systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Microprocessor Controlled Analog Systems
