SN74HC4066DT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Weight | 129.387224mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Termination | SMD/SMT |
| Resistance | 30Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 4.5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74HC4066 |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Qualification Status | Not Qualified |
| Number of Channels | 4 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 2μA |
| Max Supply Current | 2μA |
| Throw Configuration | SPST |
| Propagation Delay | 15 ns |
| Turn On Delay Time | 180 ns |
| Supply Type | Single |
| Bandwidth | 30MHz |
| Turn-Off Delay Time | 200 ns |
| On-State Resistance (Max) | 30Ohm Typ |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 42 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 0.5pF 9pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 31ns, 34ns |
| Crosstalk | -45dB @ 1MHz |
| Switching | MAKE-BEFORE-BREAK |
| Switch-on Time-Max | 36ns |
| Voltage - Supply, Single (V+) | 2V~6V |
| Normal Position | NO |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74HC4066DT Overview
The electrical component comes in 14-SOIC (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. It is mounted in the position Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Extended operating temperature around -40°C~85°C TA. 14 terminations have been made so far. This electronic part offers high-quality output due to its 4 channels. A 4.5V voltage supply should turn on and run the electronic component. Into the electrical component body are injected 14 pins. Circuits based on SPST - NO switching are used to construct these analog switch ics. Use 74HC4066 to search for variants of the digital switches. Analog switches have 30Ohm internal resistance. You can find the functions of the 14 pins in the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 6V to the switch device in normal circumstances. The digital multiplexer has a low cost Single supply. The lowest voltage fed to the electronic component should be 2V. 2μA current would be enough for this multiplexer to operate. This analogue multiplexer requires a voltage of 2V~6V when it drains from a single voltage supply. The analogue multiplexer may be damaged if voltage is greater than 2μA. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. There are 30MHz bandwidths for data transfer.
SN74HC4066DT Features
4 Channels
Switch Circuit: SPST - NO
2μA Supply Current
Bandwidth: 30MHz
SN74HC4066DT Applications
There are a lot of Texas Instruments SN74HC4066DT Analog Switches & Multiplexers ICs applications.
- Microwave transmission systems
- PBX interfaces
- Routers
- SDH/SONET multiplexers
- Communication systems
- Voice over IP/DSL – Integrated Access Devices, Smart
- Fault Tolerant Systems
- Communications systems
- CSU
- HDTV
