SN74HC4066PW
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Weight | 57.209338mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Resistance | 85Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 4.5V |
| Base Part Number | 74HC4066 |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Operating Supply Voltage | 5V |
| Number of Channels | 4 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 2μA |
| Max Supply Current | 2μA |
| Throw Configuration | SPST |
| Propagation Delay | 15 ns |
| Turn On Delay Time | 38 ns |
| Supply Type | Single |
| Bandwidth | 30MHz |
| Turn-Off Delay Time | 43 ns |
| On-State Resistance (Max) | 30Ohm Typ |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 42 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 0.5pF 9pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 31ns, 34ns |
| Crosstalk | -45dB @ 1MHz |
| Switching | MAKE-BEFORE-BREAK |
| Switch-on Time-Max | 36ns |
| Voltage - Supply, Single (V+) | 2V~6V |
| Normal Position | NO |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74HC4066PW Overview
Due to its 14-TSSOP (0.173, 4.40mm Width) packaging, the electronic part is convenient for international shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tube. This analog switch is mounted in Surface Mount. Multiplexer and demultiplexer circuits have a number 1:1. Operating temperature extended to -40°C~85°C TA. In total, 14 terminations have occurred. A electrical component with 4 channels is capable of high-quality output. Turning on and running the electrical part should be easy with a 4.5V voltage supply. Electronic part bodies are injected with 14 pins. These analog multiplexers are built based on SPST - NO switching circuits. Use 74HC4066 to search for variants of the digital switches. An switch multiplexer with 85Ohm internal resistance has a value of 85Ohm. Datasheets for 14 pin functions are available upon request. The analog multiplexer shown here is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 6V. Analogue multiplexers of the Single supply type that are cost-effective. 2V should be the lowest voltage fed to the electronic component. For this multiplexer to operate, 2μA current would be sufficient. The voltage required by this switch device is 2V~6V, draining from a single voltage supply. The analogue multiplexer may be damaged if voltage is greater than 2μA. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. A voltage of 5V can be used to operate the electronic component. A 30MHz-bandwidth can be used for data transfer.
SN74HC4066PW Features
4 Channels
Switch Circuit: SPST - NO
2μA Supply Current
Bandwidth: 30MHz
SN74HC4066PW Applications
There are a lot of Texas Instruments SN74HC4066PW Analog Switches & Multiplexers ICs applications.
- E1 Network Equipment
- Wireless Local Loop
- Multi-Line E1 Interface Cards
- DSLAMs
- Fiber In The Loop (FITL)
- SDH
- PDAs
- Medical
- ATM
- High speed data transmission line cards
