SN74HC4851N
| Parameters | |
|---|---|
| Min Supply Voltage | 2V |
| Operating Supply Current | 2μA |
| Nominal Supply Current | 2μA |
| Number of Bits | 8 |
| Propagation Delay | 25 ns |
| Turn On Delay Time | 95 ns |
| Logic Function | Demultiplexer, Multiplexer |
| Input Voltage (Max) | 6V |
| Supply Type | Single |
| Supply Current-Max (Isup) | 0.04mA |
| Turn-Off Delay Time | 95 ns |
| On-State Resistance (Max) | 195Ohm |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Current - Leakage (IS(off)) (Max) | 200nA |
| Channel Capacitance (CS(off), CD(off)) | 22pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Time (Ton, Toff) (Max) | 78ns, 78ns |
| Channel-to-Channel Matching (ΔRon) | 3 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 90ns |
| Switch-off Time-Max | 90ns |
| Voltage - Supply, Single (V+) | 2V~6V |
| Normal Position | NC |
| Signal Current-Max | 0.05A |
| Height | 5.08mm |
| Length | 19.3mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 951.693491mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 195Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 2.54mm |
| Base Part Number | 74HC4851 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 6V |
SN74HC4851N Overview
Due to its 16-DIP (0.300, 7.62mm) packaging, the electronic part is convenient for international shipping. This packaging method provides high reliability because it uses advanced packaging techniques. Multiplexers like this are mounted in the Through Hole position. The ratio between the number of multiplexer and demultiplexer circuits is 8:1. The operating temperature is extended to around -40°C~125°C TA. Totally, there are 16 terminations. The electronic part provides high-quality output because it has 1 channels. With a 3V voltage supply, the electrical component should be turned on and run. As part of the design of the 16 series, this electronic part has been incorporated into the system. A total of 1 circuits make up this switch device. 74HC4851 can be used to search for analog multiplexer variants. In this multiplexer, the internal resistance is 195Ohm. Datasheets for functions of 16 pins are available. Multiplexer or Switches is a typical switch device. A voltage higher than 6V should not normally be supplied to the switches. The analog switch ic is of the Single supply type and is cost-effective. The lowest voltage fed to the electronic component should be 2V. The switch device would be able to operate with 2μA current. This analogue multiplexer requires a voltage of 2V~6V when it drains from a single voltage supply. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. 8-bit conductivity is possible.
SN74HC4851N Features
1 Channels
2μA Supply Current
8-Bit
SN74HC4851N Applications
There are a lot of Texas Instruments SN74HC4851N Analog Switches & Multiplexers ICs applications.
- Voice over IP/DSL – Integrated Access Devices, Smart
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Communication systems
- Microprocessor controlled systems
- Multiplexers
- Remote wireless modules
- Industrial and process control systems
- Optical Applications
- SDH/SONET multiplexers
- Audio and video switching
