SN74HC4851PWR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Weight | 61.887009mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 195Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Base Part Number | 74HC4851 |
| Pin Count | 16 |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 2μA |
| Nominal Supply Current | 2μA |
| Propagation Delay | 25 ns |
| Turn On Delay Time | 95 ns |
| Logic Function | Demultiplexer, Multiplexer |
| Input Voltage (Max) | 6V |
| Number of Inputs | 8 |
| Supply Type | Single |
| Supply Current-Max (Isup) | 0.04mA |
| Turn-Off Delay Time | 95 ns |
| On-State Resistance (Max) | 195Ohm |
| High Level Output Current | 25mA |
| Low Level Output Current | 25mA |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Current - Leakage (IS(off)) (Max) | 200nA |
| Channel Capacitance (CS(off), CD(off)) | 22pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Time (Ton, Toff) (Max) | 78ns, 78ns |
| Channel-to-Channel Matching (ΔRon) | 3 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 90ns |
| Switch-off Time-Max | 90ns |
| Voltage - Supply, Single (V+) | 2V~6V |
| Normal Position | NC |
| Signal Current-Max | 0.05A |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74HC4851PWR Overview
As the electronic part is packed in 16-TSSOP (0.173, 4.40mm Width), international shipping is convenient. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. This analog switch is mounted in Surface Mount. 8:1 is the number of circuits in the multiplexer and demultiplexer. Temperatures around -40°C~125°C TA are extended for operation. In total, there have been 16 terminations. Due to its 1 channels, the electrical component produces high-quality output. With a 3V voltage supply, the electrical component should be turned on and run. The electrical component body receives 16 pins. A total of 1 circuits make up this switch device. Look for analog switch ic variants by searching with 74HC4851. A 195Ohm internal resistance characterizes this multiplexer. You can find the functions of the 16 pins in the datasheets. It is a typical Multiplexer or Switches analog multiplexer. Multiplexers should not be powered above 6V in normal situations. A cost-effective Single supply type analogue multiplexer. It is recommended that the electrical component receives a voltage of 2V. 2μA current would be enough for this multiplexer to operate. Analogue multiplexers require a 2V~6V voltage to drain from a single voltage supply. Operating 8 inputs is required.
SN74HC4851PWR Features
1 Channels
2μA Supply Current
SN74HC4851PWR Applications
There are a lot of Texas Instruments SN74HC4851PWR Analog Switches & Multiplexers ICs applications.
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- PBX interfaces
- T1/E1 Terminals
- PDH Multiplexers
- Frame Relay Equipment
- Digital access cross connects
- Battery Powered Instruments
- Battery Powered Systems
- Intelligent PBX
- E1 Multiplexer
