SN74HC4852DR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 141.690917mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 195Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Base Part Number | 74HC4852 |
| Pin Count | 16 |
| Number of Outputs | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 2μA |
| Load Capacitance | 50pF |
| Nominal Supply Current | 2μA |
| Number of Bits | 4 |
| Throw Configuration | 4PST |
| Propagation Delay | 38 ns |
| Turn On Delay Time | 47.5 ns |
| Family | HC/UH |
| Logic Function | Demultiplexer, Multiplexer |
| Number of Inputs | 8 |
| Output Characteristics | 3-STATE |
| Supply Type | Single |
| Turn-Off Delay Time | 100 ns |
| Output Polarity | TRUE |
| Logic IC Type | MULTIPLEXER AND DEMUX/DECODER |
| On-State Resistance (Max) | 195Ohm |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Power Supply Current-Max (ICC) | 0.01mA |
| Current - Leakage (IS(off)) (Max) | 200nA |
| Channel Capacitance (CS(off), CD(off)) | 22pF |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 39ns, 78ns |
| Channel-to-Channel Matching (ΔRon) | 3 Ω |
| Voltage - Supply, Single (V+) | 2V~6V |
| Height | 1.75mm |
| Length | 9.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74HC4852DR Overview
Packed in 16-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. It is mounted in the position Surface Mount. Multiplexers and demultiplexers have a number of circuits 4:1. An extended operating temperature of -40°C~125°C TA degrees Celsius. A total of 16 terminations have been recorded. An 3V voltage supply should allow the electrical part to be turned on and run. It is part of the design of the 16 series that this electronic component is included. These analog multiplexers are built based on SP4T switching circuits. Circuits number 2 make up this analogue multiplexer. Use 74HC4852 to search for variants of the digital switches. This digital multiplexer has 195Ohm internal resistance. For functions related to 16 pins, please refer to the datasheets. It is normally recommended that users do not supply the multiplexer with voltages higher than 6V. Analogue multiplexers of the Single supply type that are cost-effective. It is recommended that the electrical component receives a voltage of 2V. The analogue multiplexer could operate on 2μA current. Draining from a single voltage supply, this analog switch requires a voltage of 2V~6V. The 8 inputs need to be operated in order to work. A analog switch ics with 4 outputs is included. The switch device is capable of conducting in a 4-bit mode.
SN74HC4852DR Features
Switch Circuit: SP4T
2μA Supply Current
4-Bit
SN74HC4852DR Applications
There are a lot of Texas Instruments SN74HC4852DR Analog Switches & Multiplexers ICs applications.
- Sample-and-hold systems
- High-Voltage
- Communication systems
- Signal routing between systems
- E1 Multiplexer
- Public switching systems
- PDH Multiplexers
- Relay replacements
- Fiber to the Home
- PBX interfaces
