SN74HC4852N
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 951.693491mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 650Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74HC4852 |
| Pin Count | 16 |
| Number of Outputs | 4 |
| Qualification Status | Not Qualified |
| Polarity | Non-Inverting |
| Number of Circuits | 2 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 2μA |
| Load Capacitance | 50pF |
| Nominal Supply Current | 2μA |
| Number of Bits | 4 |
| Throw Configuration | 4PST |
| Propagation Delay | 33 ns |
| Turn On Delay Time | 47.5 ns |
| Family | HC/UH |
| Logic Function | Demultiplexer, Multiplexer |
| Output Characteristics | 3-STATE |
| Supply Type | Single |
| Turn-Off Delay Time | 100 ns |
| Logic IC Type | MULTIPLEXER AND DEMUX/DECODER |
| On-State Resistance (Max) | 195Ohm |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Power Supply Current-Max (ICC) | 0.01mA |
| Current - Leakage (IS(off)) (Max) | 200nA |
| Channel Capacitance (CS(off), CD(off)) | 22pF |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 39ns, 78ns |
| Channel-to-Channel Matching (ΔRon) | 3 Ω |
| Voltage - Supply, Single (V+) | 2V~6V |
| Height | 5.08mm |
| Length | 19.3mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74HC4852N Overview
The electrical component comes in 16-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. To ensure high reliability, a new packaging method Tube is used. Multiplexers like this are mounted in the Through Hole position. Multiplexers and demultiplexers have a ratio of 4:1. Around -40°C~85°C TA is the extended operating temperature. Total terminations are 16. A 3V voltage supply should turn on and run the electronic component. There are 16 pins injected into the electronic part body. Multiplexers built on a SP4T switching circuit are built. A 2 circuit is present in this switch device. If you are looking for variants of the digital switch, trying search with 74HC4852. Analog switches have 650Ohm internal resistance. The datasheets for the 16 pins explain the functions. A voltage higher than 6V should not normally be supplied to the switches. The analog switch ic is of the Single supply type and is cost-effective. 2V is the lowest voltage that should be fed to the electronic electronic part. This digital switch can be operated with a current of 2μA. Using a single voltage supply, this switch device consumes 2V~6V volts. The analogue multiplexer has 4 outputs. 4-bit conductivity is possible.
SN74HC4852N Features
Switch Circuit: SP4T
2μA Supply Current
4-Bit
SN74HC4852N Applications
There are a lot of Texas Instruments SN74HC4852N Analog Switches & Multiplexers ICs applications.
- Sample-and-hold systems
- Intelligent PBX
- Battery-powered systems
- Imaging
- Transmit
- Communications systems
- Mechanical reed relay replacement
- Cross Connects
- Modems
- Voice over IP/DSL – Integrated Access Devices, Smart
