SN74HC574PWE4
| Parameters | |
|---|---|
| Clock Edge Trigger Type | Positive Edge |
| Length | 6.5mm |
| Width | 4.4mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Mount | Surface Mount |
| Package / Case | TSSOP |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Packaging | Rail/Tube |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Frequency | 40MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Temperature Grade | INDUSTRIAL |
| Number of Circuits | 8 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Current - Output | 7.8mA |
| Number of Bits | 8 |
| Propagation Delay | 265 ns |
| Turn On Delay Time | 24 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Logic IC Type | BUS DRIVER |
| Max I(ol) | 0.006 A |
| High Level Output Current | -7.8mA |
| Low Level Output Current | 7.8mA |
| Number of Input Lines | 3 |
| Number of Output Lines | 1 |
SN74HC574PWE4 Overview
TSSOPis the way it is packaged. It is contained within the Rail/Tubepackage. 20terminations have occurred. The D flip flop is powered by a voltage of 5V . This D flip flop belongs to the family of HC/UH. A part of the electronic system is mounted in the way of Surface Mount. The electronic flip flop is designed with pins 20. In this device, the clock edge trigger type is Positive Edge. This device has the base part number FF/Latches. It is designed with 8bits. In order to achieve its superior flexibility, 8 circuits are used. The flip flop has 2embedded ports. In order to achieve high efficiency, the supply voltage should be maintained at 5V. There are no output lines on the JK flip flop. This input has 3lines in it. A -7.8mAvalue is set for the high level output current. 7.8mAis set as the low level output current. If the operating temperature is lower than 85°C, it is recommended. If the operating temperature is higher than -40°C, the system should operate properly. It is powered by 2V as its minimum supply voltage. It supports the maximal supply voltage of 6V. A frequency of 40MHzcan be achieved. BUS DRIVERis used as the logic IC in this D flip flop. A total of 1 functions are provided by this T flip flop. 20pins are provided on the D latch. It features maximum design flexibility due to the 7.8mA output current.
SN74HC574PWE4 Features
Rail/Tube package
20 pins
8 Bits
1 Functions
20 pin count
SN74HC574PWE4 Applications
There are a lot of Texas Instruments SN74HC574PWE4 Flip Flops applications.
- Counters
- Computing
- Differential Individual
- QML qualified product
- Frequency division
- Memory
- Storage Registers
- Cold spare funcion
- Digital electronics systems
- Asynchronous counter
