SN74HC74D
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Weight | 122.413241mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74HC74 |
| Function | Set(Preset) and Reset |
| Output Voltage | 5V |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Channels | 2 |
| Load Capacitance | 50pF |
| Output Current | 5.2mA |
| Clock Frequency | 60MHz |
| Propagation Delay | 15 ns |
| Quiescent Current | 4μA |
| Turn On Delay Time | 15 ns |
| Family | HC/UH |
| Logic Function | AND, D-Type, Flip-Flop |
| Number of Inputs | 4 |
| Current - Output High, Low | 5.2mA 5.2mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 15ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Clock Edge Trigger Type | Positive Edge |
| Max Junction Temperature (Tj) | 150°C |
| Ambient Temperature Range High | 85°C |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74HC74D Overview
14-SOIC (0.154, 3.90mm Width)is the packaging method. The package Tubecontains it. It is configured with Differentialas an output. The trigger it is configured with uses Positive Edge. There is an electronic component mounted in the way of Surface Mount. Powered by a 2V~6Vvolt supply, it operates as follows. It is operating at -40°C~85°C TA. This electronic flip flop is of type D-Type. The FPGA belongs to the 74HC series. This D flip flop should not have a frequency greater than 60MHz. A total of 14terminations have been recorded. The 74HC74 family contains it. It is powered from a supply voltage of 5V. This JK flip flop has a 3pFfarad input capacitance. The electronic device belongs to the HC/UHfamily. A part of the electronic system is mounted in the way of Surface Mount. With its 14pins, it is designed to work with most electronic flip flops. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. Vsup reaches its maximum value at 6V. Normally, the supply voltage (Vsup) should be above 2V. A high level of efficiency can be achieved by maintaining the supply voltage at 5V. The output current of 5.2mA makes it feature maximum design flexibility. It consumes 4μA of quiescent current without being affected by external factors. There are 2 channels available. There are 4 inputs.
SN74HC74D Features
Tube package
74HC series
14 pins
SN74HC74D Applications
There are a lot of Texas Instruments SN74HC74D Flip Flops applications.
- Latch
- Counters
- Shift registers
- ESCC
- Data transfer
- Data storage
- Storage registers
- Storage Registers
- Patented noise
- Common Clocks
