SN74HC74DR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Weight | 122.413241mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74HC |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74HC74 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Channels | 2 |
| Load Capacitance | 50pF |
| Nominal Supply Current | 40μA |
| Output Current | 5.2mA |
| Clock Frequency | 60MHz |
| Propagation Delay | 175 ns |
| Quiescent Current | 4μA |
| Turn On Delay Time | 15 ns |
| Family | HC/UH |
| Logic Function | AND, D-Type, Flip-Flop |
| Number of Inputs | 4 |
| Current - Output High, Low | 5.2mA 5.2mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 15ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Clock Edge Trigger Type | Positive Edge |
| Max Junction Temperature (Tj) | 150°C |
| Ambient Temperature Range High | 85°C |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74HC74DR Overview
As a result, it is packaged as 14-SOIC (0.154, 3.90mm Width). The package Tape & Reel (TR)contains it. There is a Differentialoutput configured with it. The trigger configured with it uses Positive Edge. There is an electronic component mounted in the way of Surface Mount. A 2V~6Vsupply voltage is required for it to operate. A temperature of -40°C~85°C TAis used in the operation. This logic flip flop is classified as type D-Type. The FPGA belongs to the 74HC series. It should not exceed 60MHzin terms of its output frequency. A total of 14terminations have been recorded. It is a member of the 74HC74 family. A voltage of 5V is used as the power supply for this D latch. Input capacitance of this device is 3pF farads. Devices in the HC/UHfamily are electronic devices. It is mounted in the way of Surface Mount. As you can see from the design, it has pins with 14. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. The part you are looking for is included in FF/Latches. It reaches 6Vwhen the maximum supply voltage (Vsup) is applied. A normal operating voltage (Vsup) should remain above 2V. As a result of its reliable performance, this T flip flop is suitable for TR. For high efficiency, the supply voltage should be set to 5V. It offers maximum design flexibility with its output current of 5.2mA. Despite external influences, it consumes 4μAof quiescent current. It is reported that there are 2 channels. Inputs are set to 4.
SN74HC74DR Features
Tape & Reel (TR) package
74HC series
14 pins
SN74HC74DR Applications
There are a lot of Texas Instruments SN74HC74DR Flip Flops applications.
- Frequency Divider circuits
- Shift Registers
- Single Up Count-Control Line
- Guaranteed simultaneous switching noise level
- Functionally equivalent to the MC10/100EL29
- Pattern generators
- ATE
- Power down protection
- Cold spare funcion
- Control circuits
