SN74HC74NSR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 14 |
| Weight | 208.312296mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74HC74 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Output Current | 5.2mA |
| Clock Frequency | 60MHz |
| Propagation Delay | 290 ns |
| Quiescent Current | 4μA |
| Turn On Delay Time | 15 ns |
| Family | HC/UH |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Output High, Low | 5.2mA 5.2mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 30ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 4 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2mm |
| Length | 10.3mm |
| Width | 5.3mm |
| Thickness | 1.95mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74HC74NSR Overview
The flip flop is packaged in 14-SOIC (0.209, 5.30mm Width). D flip flop is embedded in the Cut Tape (CT) package. T flip flop uses Differentialas its output configuration. This trigger uses the value Positive Edge. There is an electrical part that is mounted in the way of Surface Mount. The supply voltage is set to 2V~6V. It is at -40°C~85°C TAdegrees Celsius that the system is operating. This logic flip flop is classified as type D-Type. In terms of FPGAs, it belongs to the 74HC series. You should not exceed 60MHzin the output frequency of the device. In 14terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. JK flip flop belongs to 74HC74 family. Power is provided by a 5V supply. The input capacitance of this JK flip flopis 3pF farads. In this case, the D flip flop belongs to the HC/UHfamily. In this case, the electronic component is mounted in the way of Surface Mount. A total of 14pins are provided on this board. A Positive Edgeclock edge trigger is used in this device. This device is part of the FF/Latchesbase part number family. In this case, the maximum supply voltage (Vsup) reaches 6V. Normally, the supply voltage (Vsup) should be above 2V. The superior flexibility of this product is achieved by using 2 circuits. In light of its reliable performance, this T flip flop is well suited for TR. In order to ensure high efficiency, the supply voltage should remain at 5V. The 5.2mA output current allows it to be designed with the greatest amount of flexibility. This input has 4lines. It consumes a total of 4μA quiescent current at any given time.
SN74HC74NSR Features
Cut Tape (CT) package
74HC series
14 pins
SN74HC74NSR Applications
There are a lot of Texas Instruments SN74HC74NSR Flip Flops applications.
- Divide a clock signal by 2 or 4
- Data Synchronizers
- Test & Measurement
- Safety Clamp
- Latch
- QML qualified product
- Power down protection
- Load Control
- Pattern generators
- Latch-up performance
