SN74HC74PWR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Weight | 57.209338mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74HC74 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Nominal Supply Current | 40μA |
| Output Current | 5.2mA |
| Clock Frequency | 60MHz |
| Propagation Delay | 37 ns |
| Turn On Delay Time | 15 ns |
| Family | HC/UH |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 5.2mA 5.2mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 30ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 4 |
| Clock Edge Trigger Type | Positive Edge |
| Max Junction Temperature (Tj) | 150°C |
| Ambient Temperature Range High | 85°C |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74HC74PWR Overview
The item is packaged in 14-TSSOP (0.173, 4.40mm Width)cases. There is an embedded version in the package Cut Tape (CT). T flip flop is configured with an output of Differential. It is configured with the trigger Positive Edge. In this case, the electronic component is mounted in the way of Surface Mount. With a supply voltage of 2V~6V volts, it operates. The operating temperature is -40°C~85°C TA. D-Typeis the type of this D latch. It is a type of FPGA belonging to the 74HC series. Its output frequency should not exceed 60MHz. This process consumes 4μA quiescents. Currently, there are 14 terminations. D latch belongs to the 74HC74 family. The power supply voltage is 5V. Its input capacitance is 3pF farads. An electronic device belonging to the family HC/UHcan be found here. In this case, the electronic component is mounted in the way of Surface Mount. The electronic flip flop is designed with pins 14. This device has Positive Edgeas its clock edge trigger type. It is part of the FF/Latchesbase part number family. Vsup reaches its maximum value at 6V. The supply voltage (Vsup) should be maintained above 2V for normal operation. Its flexibility is enhanced by 2 circuits. A reliable performance of this D flip flop makes it well suited for use in TR. High efficiency requires the supply voltage to be maintained at 5V. Its output current of 5.2mAallows for maximum design flexibility. Currently, there are 4 lines of input.
SN74HC74PWR Features
Cut Tape (CT) package
74HC series
14 pins
SN74HC74PWR Applications
There are a lot of Texas Instruments SN74HC74PWR Flip Flops applications.
- Shift registers
- Circuit Design
- Clock pulse
- Buffer registers
- Event Detectors
- Control circuits
- Synchronous counter
- Single Up Count-Control Line
- ESD protection
- Guaranteed simultaneous switching noise level
