SN74HCT273DW
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74HCT273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Channels | 8 |
| Load Capacitance | 50pF |
| Output Current | 4mA |
| Number of Bits | 8 |
| Clock Frequency | 37MHz |
| Propagation Delay | 42 ns |
| Turn On Delay Time | 15 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 4mA 4mA |
| Max I(ol) | 0.004 A |
| Max Propagation Delay @ V, Max CL | 29ns @ 5.5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74HCT273DW Overview
20-SOIC (0.295, 7.50mm Width)is the packaging method. D flip flop is embedded in the Tube package. There is a Non-Invertedoutput configured with it. It is configured with a trigger that uses a value of Positive Edge. Surface Mountis occupied by this electronic component. Powered by a 4.5V~5.5Vvolt supply, it operates as follows. Temperature is set to -40°C~85°C TA. There is D-Type type of electronic flip flop associated with this device. In this case, it is a type of FPGA belonging to the 74HCT series. This D flip flop should not have a frequency greater than 37MHz. The list contains 1 elements. Despite external influences, it consumes 8μAof quiescent current. A total of 20terminations have been recorded. If you search by 74HCT273, you will find similar parts. It is powered from a supply voltage of 5V. The input capacitance of this T flip flop is 3pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. Devices in the HCTfamily are electronic devices. There is an electronic component mounted in the way of Surface Mount. This board has 20 pins. There is a clock edge trigger type of Positive Edgeon this device. This part is included in FF/Latches. The flip flop is designed with 8bits. The power supply is 5V. High efficiency requires the supply voltage to be maintained at 5V. With a current output of 4mA , it offers maximum design flexibility. This input has 3lines. Currently, there are 8 channels available.
SN74HCT273DW Features
Tube package
74HCT series
20 pins
8 Bits
5V power supplies
SN74HCT273DW Applications
There are a lot of Texas Instruments SN74HCT273DW Flip Flops applications.
- Shift Registers
- Counters
- Load Control
- Patented noise
- Data storage
- Data Synchronizers
- ESD performance
- Single Up Count-Control Line
- Clock pulse
- Latch
