SN74HCT273DWG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74HCT273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Load Capacitance | 50pF |
| Number of Bits | 8 |
| Clock Frequency | 37MHz |
| Propagation Delay | 34 ns |
| Turn On Delay Time | 15 ns |
| Family | HCT |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 4mA 4mA |
| Max I(ol) | 0.004 A |
| Max Propagation Delay @ V, Max CL | 29ns @ 5.5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 8 |
| fmax-Min | 23 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74HCT273DWG4 Overview
In the form of 20-SOIC (0.295, 7.50mm Width), it has been packaged. The Tubepackage contains it. This output is configured with Non-Inverted. The trigger it is configured with uses Positive Edge. Surface Mountis occupied by this electronic component. Powered by a 4.5V~5.5Vvolt supply, it operates as follows. In the operating environment, the temperature is -40°C~85°C TA. It is an electronic flip flop with the type D-Type. JK flip flop is a part of the 74HCTseries of FPGAs. It should not exceed 37MHzin its output frequency. D latch consists of 1 elements. It consumes 8μA of quiescent A total of 20 terminations have been made. You can search similar parts based on 74HCT273. The power source is powered by 5V. The input capacitance of this T flip flop is 3pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. An electronic device belonging to the family HCTcan be found here. Surface Mount mounts this electronic component. With its 20pins, it is designed to work with most electronic flip flops. Its clock edge trigger type is Positive Edge. The RS flip flops belongs to FF/Latches base part number. There are 8bits in its design. In order for the device to operate, it requires 5V power supplies. The supply voltage should be maintained at 5V for high efficiency. 8input lines are available for you to choose from.
SN74HCT273DWG4 Features
Tube package
74HCT series
20 pins
8 Bits
5V power supplies
SN74HCT273DWG4 Applications
There are a lot of Texas Instruments SN74HCT273DWG4 Flip Flops applications.
- Computing
- CMOS Process
- Storage Registers
- Count Modes
- Frequency Divider circuits
- Divide a clock signal by 2 or 4
- Storage registers
- Common Clocks
- Dynamic threshold performance
- Bounce elimination switch
