SN74HCT273DWRE4
| Parameters | |
|---|---|
| Turn On Delay Time | 15 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Logic IC Type | D FLIP-FLOP |
| Max I(ol) | 0.004 A |
| High Level Output Current | -4mA |
| Low Level Output Current | 4mA |
| Number of Input Lines | 3 |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latch |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Frequency | 37MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Number of Circuits | 8 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Bits | 8 |
| Propagation Delay | 34 ns |
SN74HCT273DWRE4 Overview
In the form of SOIC, it has been packaged. The Tape & Reel (TR)package contains it. There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. The power source is powered by 5V. The electronic device belongs to the HCTfamily. In this case, the electronic component is mounted in the way of Surface Mount. 20pins are included in its design. This device exhibits a clock edge trigger type of Positive Edge. The part you are looking for is included in FF/Latch. An electronic part with 8bits has been designed. Due to its superior flexibility, it uses 8 circuits. On the basis of its reliable performance, this D flip flop is well suited for use with TAPE AND REEL. The power supply is 5V. In order to achieve high efficiency, the supply voltage should be maintained at 5V. To operate, the chip has a total of 1 output lines. It has 3lines. -4mAis set as the high level output current. There is no low level output current set at 4mA. Ideally, the operating temperature should be lower than 85°C. It is recommended that the operating temperature is higher than -40°C. In order for it to operate, a supply voltage of 4.5Vis required. 5.5Vis the maximum supply voltage supported by it. It is possible to achieve a frequency of 37MHz. The logic IC it adopts is D FLIP-FLOP. It is equipped with 1 Functions . The D latch is equipped with 20 pins.
SN74HCT273DWRE4 Features
Tape & Reel (TR) package
20 pins
8 Bits
5V power supplies
1 Functions
20 pin count
SN74HCT273DWRE4 Applications
There are a lot of Texas Instruments SN74HCT273DWRE4 Flip Flops applications.
- Balanced Propagation Delays
- Set-reset capability
- Single Up Count-Control Line
- Counters
- Test & Measurement
- Cold spare funcion
- Frequency Dividers
- Storage registers
- Consumer
- ATE
