SN74HCT273PWE4
| Parameters | |
|---|---|
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Package / Case | TSSOP |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Packing Method | TUBE |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Frequency | 37MHz |
| Pin Count | 20 |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Number of Circuits | 8 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Bits | 8 |
| Propagation Delay | 42 ns |
| Turn On Delay Time | 15 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Logic IC Type | D FLIP-FLOP |
| Max I(ol) | 0.004 A |
| High Level Output Current | -4mA |
| Low Level Output Current | 4mA |
| Number of Input Lines | 3 |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.2mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74HCT273PWE4 Overview
The flip flop is packaged in TSSOP. A total of 20terminations have been recorded. Power is supplied from a voltage of 5V volts. This D flip flop belongs to the family of HCT. The electronic part is mounted in the way of Surface Mount. 20pins are included in its design. Its clock edge trigger type is Positive Edge. The part you are looking for is included in FF/Latches. It is designed with 8bits. The superior flexibility of this circuit is achieved by using 8 circuits. This D flip flop is well suited for TUBE based on its reliable performance. The D latch operates on 5V volts. For high efficiency, the supply voltage should be set to 5V. In order for the chip to function, it has 1output lines. Currently, there are 3 input lines present. -4mAis set as the high level output current. Low level output current is set to 4mA. There should be a temperature below 85°Cduring operation. If the operating temperature is higher than -40°C, the system should operate properly. It operates with the minimal supply voltage of 4.5V. 5.5Vis the maximum supply voltage it supports. This can be achieved at a frequency of 37MHz. It adopts a logic IC of type D FLIP-FLOP. A total of 1 functions are provided by this T flip flop. There are 20 pins on the D latch.
SN74HCT273PWE4 Features
20 pins
8 Bits
5V power supplies
1 Functions
20 pin count
SN74HCT273PWE4 Applications
There are a lot of Texas Instruments SN74HCT273PWE4 Flip Flops applications.
- Set-reset capability
- Memory
- Instrumentation
- Test & Measurement
- Differential Individual
- Frequency Divider circuits
- Data transfer
- Guaranteed simultaneous switching noise level
- Control circuits
- Counters
