SN74HCT273PWRG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | TSSOP |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Frequency | 37MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Propagation Delay | 34 ns |
| Turn On Delay Time | 15 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Logic IC Type | D FLIP-FLOP |
| Max I(ol) | 0.004 A |
| Number of Bits per Element | 8 |
| High Level Output Current | -4mA |
| Low Level Output Current | 4mA |
| fmax-Min | 23 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Length | 6.5mm |
| Width | 4.4mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74HCT273PWRG4 Overview
It is embeded in TSSOP case. It is included in the package Tape & Reel (TR). A total of 1elements are present in it. There have been 20 terminations. A voltage of 5V is used to power it. HCTis the family of this D flip flop. It is mounted by the way of Surface Mount. With its 20pins, it is designed to work with most electronic flip flops. This device exhibits a clock edge trigger type of Positive Edge. The RS flip flops belongs to FF/Latches base part number. Considering the reliability of this T flip flop, it is well suited for TR. An electrical current of 5V volts is applied to it. For high efficiency, the supply voltage should be kept at 5V. The high level output current is set to -4mA. There is no low level output current set at 4mA. There should be a temperature below 85°Cduring operation. If the operating temperature is higher than -40°C, the system should operate properly. Initially, it requires a voltage of 4.5V as the minimum supply voltage. It is capable of supporting a maximum supply voltage of 5.5V. This frequency can be achieved 37MHz. D FLIP-FLOPis used as the logic IC in this D flip flop. Currently, it is equipped with 1 functions . It is equipped with 20 pins.
SN74HCT273PWRG4 Features
Tape & Reel (TR) package
20 pins
5V power supplies
1 Functions
20 pin count
SN74HCT273PWRG4 Applications
There are a lot of Texas Instruments SN74HCT273PWRG4 Flip Flops applications.
- Bus hold
- Consumer
- Balanced Propagation Delays
- QML qualified product
- EMI reduction circuitry
- Bounce elimination switch
- 2 – Bit synchronous counter
- Shift Registers
- Modulo – n – counter
- Frequency Dividers
