SN74HCT374DBR
| Parameters | |
|---|---|
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 40MHz |
| Propagation Delay | 46 ns |
| Turn On Delay Time | 25 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 6mA 6mA |
| Max I(ol) | 0.006 A |
| Max Propagation Delay @ V, Max CL | 32ns @ 5.5V, 50pF |
| Prop. Delay@Nom-Sup | 45 ns |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 25000000Hz |
| Height | 2mm |
| Length | 7.2mm |
| Width | 5.3mm |
| Thickness | 1.95mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Weight | 156.687814mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74HCT374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
SN74HCT374DBR Overview
The flip flop is packaged in 20-SSOP (0.209, 5.30mm Width). There is an embedded version in the package Cut Tape (CT). As configured, the output uses Tri-State, Non-Inverted. It is configured with a trigger that uses Positive Edge. There is an electronic component mounted in the way of Surface Mount. The JK flip flop operates with an input voltage of 4.5V~5.5V volts. A temperature of -40°C~85°C TAis used in the operation. A flip flop of this type is classified as a D-Type. In FPGA terms, D flip flop is a type of 74HCTseries FPGA. You should not exceed 40MHzin the output frequency of the device. In total, it contains 1 elements. As a result, it consumes 8μA quiescent current. A total of 20terminations have been recorded. The 74HCT374 family contains it. An input voltage of 5Vpowers the D latch. JK flip flop input capacitance is 3pF farads. In terms of electronic devices, this device belongs to the HCTfamily of devices. It is mounted by the way of Surface Mount. The 20pins are designed into the board. This device has Positive Edgeas its clock edge trigger type. The part is included in FF/Latches. An electronic part with 8bits has been designed. Despite its superior flexibility, it relies on 8 circuits to achieve it. This D flip flop is well suited for TR based on its reliable performance. The D latch runs on a voltage of 5V volts. The flip flop has 2embedded ports. For high efficiency, the supply voltage should be set to 5V. As of now, there are 3input lines.
SN74HCT374DBR Features
Cut Tape (CT) package
74HCT series
20 pins
8 Bits
5V power supplies
SN74HCT374DBR Applications
There are a lot of Texas Instruments SN74HCT374DBR Flip Flops applications.
- QML qualified product
- High Performance Logic for test systems
- Count Modes
- Dynamic threshold performance
- EMI reduction circuitry
- Shift registers
- Modulo – n – counter
- ATE
- ESD protection
- Cold spare funcion
