SN74HCT374DW
| Parameters | |
|---|---|
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74HCT374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Channels | 8 |
| Number of Ports | 2 |
| Output Current | 6mA |
| Number of Bits | 8 |
| Clock Frequency | 40MHz |
| Propagation Delay | 46 ns |
| Turn On Delay Time | 25 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 6mA 6mA |
| Max I(ol) | 0.006 A |
| Max Propagation Delay @ V, Max CL | 25ns @ 5.5V, 50pF |
| Prop. Delay@Nom-Sup | 45 ns |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 25000000Hz |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
SN74HCT374DW Overview
The flip flop is packaged in a case of 20-SOIC (0.295, 7.50mm Width). A package named Tubeincludes it. This output is configured with Tri-State, Non-Inverted. It is configured with a trigger that uses a value of Positive Edge. There is an electrical part that is mounted in the way of Surface Mount. It operates with a supply voltage of 4.5V~5.5V. -40°C~85°C TAis the operating temperature. Logic flip flops of this type are classified as D-Type. In terms of FPGAs, it belongs to the 74HCT series. There should be no greater frequency than 40MHzon its output. In total, there are 1 elements. There is a consumption of 8μAof quiescent energy. There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. The 74HCT374family includes it. The power source is powered by 5V. The input capacitance of this JK flip flopis 3pF farads. In terms of electronic devices, this device belongs to the HCTfamily of devices. There is an electronic part mounted in the way of Surface Mount. As you can see from the design, it has pins with 20. There is a clock edge trigger type of Positive Edgeon this device. This device has the base part number FF/Latches. The design is based on 8bits. The D latch runs on a voltage of 5V volts. There are 2 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. The supply voltage should be maintained at 5V for high efficiency. As a result of its output current of 6mA, it is very flexible in terms of design. There are 3 input Lines, which consist of an electronic circuit connected between the ac mains and the rectifier input stage of the switching power supply. Currently, there are 8 channels available.
SN74HCT374DW Features
Tube package
74HCT series
20 pins
8 Bits
5V power supplies
SN74HCT374DW Applications
There are a lot of Texas Instruments SN74HCT374DW Flip Flops applications.
- Latch
- Safety Clamp
- Data storage
- Circuit Design
- Balanced 24 mA output drivers
- 2 – Bit synchronous counter
- Consumer
- Pattern generators
- Load Control
- Asynchronous counter
