SN74HCT574DBR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Weight | 156.687814mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74HCT574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 40MHz |
| Propagation Delay | 45 ns |
| Turn On Delay Time | 25 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 6mA 6mA |
| Max I(ol) | 0.006 A |
| Max Propagation Delay @ V, Max CL | 47ns @ 5.5V, 150pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 27000000Hz |
| Height | 2mm |
| Length | 7.2mm |
| Width | 5.3mm |
| Thickness | 1.95mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74HCT574DBR Overview
As a result, it is packaged as 20-SSOP (0.209, 5.30mm Width). D flip flop is included in the Tape & Reel (TR)package. As configured, the output uses Tri-State, Non-Inverted. There is a trigger configured with Positive Edge. Surface Mountmounts this electrical part. A voltage of 4.5V~5.5Vis used as the supply voltage. It is at -40°C~85°C TAdegrees Celsius that the system is operating. The type of this D latch is D-Type. JK flip flop is a part of the 74HCTseries of FPGAs. A frequency of 40MHzshould not be exceeded by its output. D latch consists of 1 elements. There is 8μA quiescent consumption. The number of terminations is 20. It is a member of the 74HCT574 family. The power supply voltage is 5V. The input capacitance of this T flip flop is 3pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. A device of this type belongs to the family of HCT. The electronic part is mounted in the way of Surface Mount. It is designed with 20 pins. This device has Positive Edgeas its clock edge trigger type. This part is included in FF/Latches. There are 8bits in its design. Its superior flexibility is attributed to its use of 8 circuits. This D flip flop is well suited for TR based on its reliable performance. The system runs on a power supply of 5V watts. The D flip flop is embedded with 2ports. Optimal efficiency requires a supply voltage of 5V. It has 3lines.
SN74HCT574DBR Features
Tape & Reel (TR) package
74HCT series
20 pins
8 Bits
5V power supplies
SN74HCT574DBR Applications
There are a lot of Texas Instruments SN74HCT574DBR Flip Flops applications.
- 2 – Bit synchronous counter
- Instrumentation
- ESCC
- Data transfer
- Counters
- Storage Registers
- Guaranteed simultaneous switching noise level
- Event Detectors
- Clock pulse
- Balanced 24 mA output drivers
