SN74HCT574N
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 20-DIP (0.300, 7.62mm) |
| Number of Pins | 20 |
| Weight | 1.1991g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | 74HCT574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Channels | 8 |
| Number of Ports | 2 |
| Output Current | 6mA |
| Number of Bits | 8 |
| Clock Frequency | 40MHz |
| Propagation Delay | 53 ns |
| Turn On Delay Time | 25 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 6mA 6mA |
| Max I(ol) | 0.006 A |
| Max Propagation Delay @ V, Max CL | 47ns @ 5.5V, 150pF |
| Prop. Delay@Nom-Sup | 45 ns |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 27000000Hz |
| Height | 5.08mm |
| Length | 24.33mm |
| Width | 6.35mm |
| Thickness | 4.57mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74HCT574N Overview
The flip flop is packaged in a case of 20-DIP (0.300, 7.62mm). A package named Tubeincludes it. T flip flop is configured with an output of Tri-State, Non-Inverted. It is configured with a trigger that uses a value of Positive Edge. Through Holeis occupied by this electronic component. The JK flip flop operates at 4.5V~5.5Vvolts. It is operating at -40°C~85°C TA. This D latch has the type D-Type. In this case, it is a type of FPGA belonging to the 74HCT series. There should be no greater frequency than 40MHzon its output. The list contains 1 elements. There is a consumption of 8μAof quiescent energy. There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. D latch belongs to the 74HCT574 family. An input voltage of 5Vpowers the D latch. The input capacitance of this T flip flop is 3pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. The electronic device belongs to the HCTfamily. There is an electronic component mounted in the way of Through Hole. Basically, it is designed with a set of 20 pins. This device's clock edge trigger type is Positive Edge. The part is included in FF/Latches. It is designed with 8bits. It runs on 5Vvolts of power. There are 2 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. High efficiency requires the supply voltage to be maintained at 5V. Its output current of 6mAallows for maximum design flexibility. This input has 3lines in it. The number of channels is growing strong/weak: 8.
SN74HCT574N Features
Tube package
74HCT series
20 pins
8 Bits
5V power supplies
SN74HCT574N Applications
There are a lot of Texas Instruments SN74HCT574N Flip Flops applications.
- Balanced 24 mA output drivers
- EMI reduction circuitry
- ESCC
- 2 – Bit synchronous counter
- Consumer
- Individual Asynchronous Resets
- Automotive
- Count Modes
- QML qualified product
- ESD protection
