SN74HCT574NSR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Weight | 266.712314mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74HCT574 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 40MHz |
| Propagation Delay | 53 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 25 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 6mA 6mA |
| Max I(ol) | 0.006 A |
| Max Propagation Delay @ V, Max CL | 47ns @ 5.5V, 150pF |
| Prop. Delay@Nom-Sup | 45 ns |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 27000000Hz |
| Height | 2mm |
| Length | 12.6mm |
| Width | 5.3mm |
| Thickness | 1.95mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74HCT574NSR Overview
20-SOIC (0.209, 5.30mm Width)is the way it is packaged. D flip flop is included in the Tape & Reel (TR)package. T flip flop is configured with an output of Tri-State, Non-Inverted. The trigger it is configured with uses Positive Edge. This electronic part is mounted in the way of Surface Mount. A 4.5V~5.5Vsupply voltage is required for it to operate. It is operating at -40°C~85°C TA. It is an electronic flip flop with the type D-Type. In terms of FPGAs, it belongs to the 74HCT series. There should be no greater frequency than 40MHzon its output. A total of 1elements are present in it. There have been 20 terminations. Members of the 74HCT574family make up this object. An input voltage of 5Vpowers the D latch. The input capacitance of this JK flip flopis 3pF farads. In this case, the D flip flop belongs to the HCTfamily. It is mounted in the way of Surface Mount. 20pins are included in its design. There is a clock edge trigger type of Positive Edgeon this device. This RS flip flops is a part number FF/Latches. An electronic part with 8bits has been designed. The superior flexibility of this product is achieved by using 8 circuits. In view of its reliability, this D flip flop is a good fit for TR. The D latch runs on a voltage of 5V volts. This D flip flop is equipped with 0 ports. For high efficiency, the supply voltage should be set to 5V. A total of 3input lines have been provided. There is 8μA quiescent current consumption by it.
SN74HCT574NSR Features
Tape & Reel (TR) package
74HCT series
20 pins
8 Bits
5V power supplies
SN74HCT574NSR Applications
There are a lot of Texas Instruments SN74HCT574NSR Flip Flops applications.
- Modulo – n – counter
- Individual Asynchronous Resets
- Storage registers
- Storage Registers
- Consumer
- Matched Rise and Fall
- Test & Measurement
- Convert a momentary switch to a toggle switch
- Frequency Dividers
- Parallel data storage
