SN74HCT74DG4
| Parameters | |
|---|---|
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 14 |
| Weight | 129.387224mg |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Packing Method | TUBE |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Frequency | 46MHz |
| Pin Count | 14 |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Propagation Delay | 28 ns |
| Turn On Delay Time | 18 ns |
| Family | HCT |
| Logic Function | AND, D-Type, Flip-Flop |
| Logic IC Type | D FLIP-FLOP |
| Number of Bits per Element | 1 |
| Prop. Delay@Nom-Sup | 35 ns |
| High Level Output Current | -4mA |
| Low Level Output Current | 4mA |
| Number of Input Lines | 4 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74HCT74DG4 Overview
The package is in the form of SOIC. The element count is 2 . In 14terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. An input voltage of 5Vpowers the D latch. This D flip flop belongs to the family of HCT. Surface Mount mounts this electronic component. As you can see from the design, it has pins with 14. The clock edge trigger type for this device is Positive Edge. The RS flip flops belongs to FF/Latches base part number. In view of its reliability, this D flip flop is a good fit for TUBE. The D latch runs on a voltage of 5V volts. In order to ensure high efficiency, the supply voltage should remain at 5V. A total of 4input lines have been provided. A -4mAis set for the high level output current. It is set to 4mAfor low level output current. If the operating temperature is lower than 85°C, it is recommended. It is recommended that the operating temperature be greater than -40°C. In order for it to operate, a supply voltage of 4.5Vis required. There is a maximum supply voltage of 5.5V. This can be achieved at a frequency of 46MHz. D FLIP-FLOPis used as the logic IC in this D flip flop. It is equipped with 2 Functions . It has 14 pins.
SN74HCT74DG4 Features
14 pins
5V power supplies
2 Functions
14 pin count
SN74HCT74DG4 Applications
There are a lot of Texas Instruments SN74HCT74DG4 Flip Flops applications.
- Frequency division
- Modulo – n – counter
- Patented noise
- Buffer registers
- Bus hold
- Computing
- Storage Registers
- Communications
- Latch-up performance
- Guaranteed simultaneous switching noise level
