SN74HCT74NSRE4
| Parameters | |
|---|---|
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 14 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Frequency | 46MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 14 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Propagation Delay | 28 ns |
| Turn On Delay Time | 18 ns |
| Family | HCT |
| Logic Function | AND, D-Type, Flip-Flop |
| Logic IC Type | D FLIP-FLOP |
| Number of Bits per Element | 1 |
| High Level Output Current | -4mA |
| Low Level Output Current | 4mA |
| Number of Input Lines | 4 |
| Clock Edge Trigger Type | Positive Edge |
| Width | 5.3mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Mount | Surface Mount |
| Package / Case | SOP |
| Number of Pins | 14 |
| Weight | 208.312296mg |
SN74HCT74NSRE4 Overview
The item is packaged in SOPcases. The Tape & Reel (TR)package contains it. D latch consists of 2 elements. In 14terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. It is powered from a supply voltage of 5V. The electronic device belongs to the HCTfamily. It is mounted by the way of Surface Mount. As you can see from the design, it has pins with 14. A Positive Edgeclock edge trigger is used in this device. This RS flip flops is a part number FF/Latches. In view of its reliability, this D flip flop is a good fit for TAPE AND REEL. It runs on 5Vvolts of power. For high efficiency, the supply voltage should be set to 5V. As of now, there are 4input lines. -4mA is set as the high level output current. There is no low level output current set at 4mA. There should be a temperature below 85°Cduring operation. It should be higher than -40°Cwhen the system is operating. A minimum supply voltage of 4.5V is required for these RS flip flops to operate. It supports the maximal supply voltage of 5.5V. We are able to achieve a frequency of 46MHz. It uses the logic IC D FLIP-FLOP. A total of 2 functions are provided by this T flip flop. The D latch is equipped with 14 pins.
SN74HCT74NSRE4 Features
Tape & Reel (TR) package
14 pins
5V power supplies
2 Functions
14 pin count
SN74HCT74NSRE4 Applications
There are a lot of Texas Instruments SN74HCT74NSRE4 Flip Flops applications.
- Memory
- Frequency Divider circuits
- Cold spare funcion
- Shift registers
- Event Detectors
- Frequency Dividers
- Pattern generators
- Balanced Propagation Delays
- Digital electronics systems
- Patented noise
