SN74LS374DBR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Weight | 156.687814mg |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74LS |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | TTL |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74LS374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 45pF |
| Number of Ports | 2 |
| Output Current | 24mA |
| Number of Bits | 8 |
| Clock Frequency | 50MHz |
| Propagation Delay | 28 ns |
| Turn On Delay Time | 20 ns |
| Family | LS |
| Logic Function | D-Type, Latch |
| Current - Quiescent (Iq) | 40mA |
| Current - Output High, Low | 2.6mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 28ns @ 5V, 45pF |
| Trigger Type | Positive Edge |
| Power Supply Current-Max (ICC) | 40mA |
| Number of Input Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2mm |
| Length | 7.2mm |
| Width | 5.3mm |
| Thickness | 1.95mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74LS374DBR Overview
As a result, it is packaged as 20-SSOP (0.209, 5.30mm Width). As part of the package Tape & Reel (TR), it is embedded. T flip flop uses Tri-State, Non-Invertedas its output configuration. Positive Edgeis the trigger it is configured with. Surface Mountis positioned in the way of this electronic part. A voltage of 4.75V~5.25Vis required for its operation. It is operating at 0°C~70°C TA. It belongs to the type D-Typeof flip flops. It is a type of FPGA belonging to the 74LS series. In order for it to function properly, its output frequency should not exceed 50MHz. D latch consists of 1 elements. As a result, it consumes 40mA quiescent current and is not affected by external forces. There have been 20 terminations. This D latch belongs to the family of 74LS374. A voltage of 5V provides power to the D latch. It is a member of the LSfamily of D flip flop. A part of the electronic system is mounted in the way of Surface Mount. This board has 20 pins. This device's clock edge trigger type is Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. An electronic part designed with 8bits is used in this application. The superior flexibility of this product is achieved by using 8 circuits. Due to its reliability, this T flip flop is well suited for TR. The system runs on a power supply of 5V watts. The flip flop contains 2ports. A high level of efficiency can be achieved by maintaining the supply voltage at 5V. This T flip flop features a maximum design flexibility due to its output current of 24mA. It has 3lines.
SN74LS374DBR Features
Tape & Reel (TR) package
74LS series
20 pins
8 Bits
5V power supplies
SN74LS374DBR Applications
There are a lot of Texas Instruments SN74LS374DBR Flip Flops applications.
- ESCC
- Buffered Clock
- Digital electronics systems
- Memory
- ATE
- Count Modes
- Single Down Count-Control Line
- Buffer registers
- Bounce elimination switch
- Test & Measurement
