SN74LS377DWG4
| Parameters | |
|---|---|
| Height | 2.35mm |
| Length | 12.8mm |
| Width | 7.52mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| Additional Feature | WITH HOLD MODE |
| Subcategory | FF/Latches |
| Packing Method | TUBE |
| Technology | TTL |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Frequency | 40MHz |
| Pin Count | 20 |
| Output Type | TTL |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | COMMERCIAL |
| Max Supply Voltage | 5.25V |
| Min Supply Voltage | 4.75V |
| Current - Output | 8mA |
| Propagation Delay | 27 ns |
| Turn On Delay Time | 17 ns |
| Family | LS |
| Logic Function | D-Type |
| Logic IC Type | D FLIP-FLOP |
| Number of Bits per Element | 8 |
| High Level Output Current | -400μA |
| Low Level Output Current | 8mA |
| fmax-Min | 30 MHz |
| Clock Edge Trigger Type | Positive Edge |
SN74LS377DWG4 Overview
The flip flop is packaged in a case of SOIC. T flip flop uses TTLas its output configuration. A total of 1 elements are present. A total of 20terminations have been recorded. A voltage of 5V provides power to the D latch. It belongs to the family of electronic devices known as LS. There is an electronic part that is mounted in the way of Surface Mount. The 20pins are designed into the board. This device has Positive Edgeas its clock edge trigger type. This part is included in FF/Latches. Due to its reliability, this T flip flop is well suited for TUBE. A power supply of 5Vis required to operate it. A high level of efficiency can be achieved by maintaining the supply voltage at 5V. WITH HOLD MODEis also one of its characteristics. -400μAis set as the high level output current. Low level output current is set to 8mA. A temperature below 70°Cshould be used for operation. The operating temperature should be higher than 0°C. In order for it to operate, a supply voltage of 4.75Vis required. There is a maximum supply voltage of 5.25V. A frequency of 40MHzcan be achieved. This logic IC is D FLIP-FLOP. There are 1 functions available on the JK flip flop. The JK flip flop has a pin count of 20. The output current of 8mA makes it feature maximum design flexibility.
SN74LS377DWG4 Features
20 pins
5V power supplies
1 Functions
20 pin count
SN74LS377DWG4 Applications
There are a lot of Texas Instruments SN74LS377DWG4 Flip Flops applications.
- Circuit Design
- Bus hold
- ESD performance
- Single Up Count-Control Line
- Control circuits
- Functionally equivalent to the MC10/100EL29
- Supports Live Insertion
- Computing
- Frequency Dividers
- Automotive
