SN74LV174APWR
| Parameters | |
|---|---|
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 2V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 2.5V |
| Base Part Number | 74LV174 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 3.3V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 7 |
| Load Capacitance | 50pF |
| Output Current | 12mA |
| Clock Frequency | 180MHz |
| Propagation Delay | 20.6 ns |
| Quiescent Current | 20μA |
| Turn On Delay Time | 3 ns |
| Family | LV/LV-A/LVX/H |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 12mA 12mA |
| Number of Bits per Element | 6 |
| Max Propagation Delay @ V, Max CL | 9.2ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 1.7pF |
| Number of Input Lines | 2 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 50000000Hz |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Weight | 61.887009mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74LV |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
SN74LV174APWR Overview
The item is packaged in 16-TSSOP (0.173, 4.40mm Width)cases. Package Tape & Reel (TR)embeds it. There is a Non-Invertedoutput configured with it. This trigger is configured to use Positive Edge. It is mounted in the way of Surface Mount. A supply voltage of 2V~5.5V is required for operation. The operating temperature is -40°C~85°C TA. This electronic flip flop is of type D-Type. It is a type of FPGA belonging to the 74LV series. Its output frequency should not exceed 180MHz Hz. There are 1 elements in it. There are 16 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. The 74LV174 family contains it. It is powered from a supply voltage of 2.5V. A JK flip flop with a 1.7pFfarad input capacitance is used here. The electronic device belongs to the LV/LV-A/LVX/Hfamily. A part of the electronic system is mounted in the way of Surface Mount. This board has 16 pins. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. It is included in FF/Latches. There is a 5.5Vmaximum supply voltage (Vsup). Keeping the supply voltage (Vsup) above 2V is necessary for normal operation. The superior flexibility is achieved through the use of 7 circuits. On the basis of its reliable performance, this D flip flop is well suited for use with TR. There are 3.3V power supplies attached to it. With an output current of 12mA, this device offers maximum design flexibility. It is reported that there are 2 input lines. Despite external influences, it consumes 20μAof quiescent current.
SN74LV174APWR Features
Tape & Reel (TR) package
74LV series
16 pins
3.3V power supplies
SN74LV174APWR Applications
There are a lot of Texas Instruments SN74LV174APWR Flip Flops applications.
- ESCC
- Guaranteed simultaneous switching noise level
- Matched Rise and Fall
- Memory
- Balanced 24 mA output drivers
- Buffered Clock
- Instrumentation
- Reduced system switching noise
- Bus hold
- Shift Registers
