SN74LV175AD
| Parameters | |
|---|---|
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 2V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 2.5V |
| Base Part Number | 74LV175 |
| Function | Master Reset |
| Output Type | Differential |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 3.3V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 4 |
| Load Capacitance | 50pF |
| Output Current | 12mA |
| Number of Bits | 4 |
| Clock Frequency | 165MHz |
| Propagation Delay | 23.3 ns |
| Turn On Delay Time | 3.7 ns |
| Family | LV/LV-A/LVX/H |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 20μA |
| Current - Output High, Low | 12mA 12mA |
| Max Propagation Delay @ V, Max CL | 9.3ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 1.4pF |
| Number of Output Lines | 2 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.75mm |
| Length | 9.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 141.690917mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74LV |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
SN74LV175AD Overview
The flip flop is packaged in a case of 16-SOIC (0.154, 3.90mm Width). A package named Tubeincludes it. In the configuration, Differentialis used as the output. It is configured with a trigger that uses a value of Positive Edge. This electronic part is mounted in the way of Surface Mount. A 2V~5.5Vsupply voltage is required for it to operate. A temperature of -40°C~85°C TAis used in the operation. D-Typeis the type of this D latch. In this case, it is a type of FPGA belonging to the 74LV series. It should not exceed 165MHzin its output frequency. In total, it contains 1 elements. Despite external influences, it consumes 20μAof quiescent current. Currently, there are 16 terminations. This D latch belongs to the family of 74LV175. A voltage of 2.5V is used to power it. The input capacitance of this JK flip flopis 1.4pF farads. In terms of electronic devices, this device belongs to the LV/LV-A/LVX/Hfamily of devices. This electronic part is mounted in the way of Surface Mount. With its 16pins, it is designed to work with most electronic flip flops. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. This RS flip flops is a part number FF/Latches. An electronic part with 4bits has been designed. There is a 5.5Vmaximum supply voltage (Vsup). The supply voltage (Vsup) should be maintained above 2V for normal operation. The superior flexibility of this circuit is achieved by using 4 circuits. A total of 3.3V power supplies are needed to run it. As a result of its output current of 12mA, it is very flexible in terms of design. In order for the chip to function, it has 2output lines.
SN74LV175AD Features
Tube package
74LV series
16 pins
4 Bits
3.3V power supplies
SN74LV175AD Applications
There are a lot of Texas Instruments SN74LV175AD Flip Flops applications.
- Safety Clamp
- Matched Rise and Fall
- Modulo – n – counter
- Balanced 24 mA output drivers
- High Performance Logic for test systems
- Bounce elimination switch
- Test & Measurement
- ESD performance
- Bus hold
- Shift Registers
