SN74LV273APWT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74LV |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Termination | SMD/SMT |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 2V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74LV273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 3.3V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Output Current | 12mA |
| Number of Bits | 8 |
| Clock Frequency | 160MHz |
| Propagation Delay | 25.5 ns |
| Turn On Delay Time | 4.8 ns |
| Family | LV/LV-A/LVX/H |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 20μA |
| Current - Output High, Low | 12mA 12mA |
| Max Propagation Delay @ V, Max CL | 11ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 2pF |
| Number of Input Lines | 2 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 45000000Hz |
| Height | 1.2mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74LV273APWT Overview
20-TSSOP (0.173, 4.40mm Width)is the packaging method. D flip flop is included in the Tape & Reel (TR)package. There is a Non-Invertedoutput configured with it. It is configured with a trigger that uses Positive Edge. It is mounted in the way of Surface Mount. A 2V~5.5Vsupply voltage is required for it to operate. It is operating at a temperature of -40°C~125°C TA. A flip flop of this type is classified as a D-Type. FPGAs belonging to the 74LVseries contain this type of chip. Its output frequency should not exceed 160MHz. A total of 1elements are present in it. As a result, it consumes 20μA of quiescent current without being affected by external factors. There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. The 74LV273 family contains it. A voltage of 2.5V provides power to the D latch. Input capacitance of this device is 2pF farads. The electronic device belongs to the LV/LV-A/LVX/Hfamily. It is mounted in the way of Surface Mount. As you can see from the design, it has pins with 20. There is a clock edge trigger type of Positive Edgeon this device. This part is included in FF/Latches. This flip flop is designed with 8 Bits. It reaches 5.5Vwhen the supply voltage is maximal (Vsup). If you want to maintain normal operation, you should keep the supply voltage (Vsup) above 2V. Using 8 circuits, it is highly flexible. A reliable performance of this D flip flop makes it well suited for use in TR. There are 3.3V power supplies attached to it. It offers maximum design flexibility with its output current of 12mA. It has 2lines.
SN74LV273APWT Features
Tape & Reel (TR) package
74LV series
20 pins
8 Bits
3.3V power supplies
SN74LV273APWT Applications
There are a lot of Texas Instruments SN74LV273APWT Flip Flops applications.
- Count Modes
- Instrumentation
- Modulo – n – counter
- Shift Registers
- Convert a momentary switch to a toggle switch
- Test & Measurement
- Digital electronics systems
- QML qualified product
- EMI reduction circuitry
- Reduced system switching noise
