SN74LV4052ATPWRQ1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Weight | 61.887009mg |
| Operating Temperature | -40°C~105°C TA |
| Packaging | Tape & Reel (TR) |
| Series | Automotive, AEC-Q100 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Base Part Number | 74LV4052 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 3.3V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 20μA |
| Number of Bits | 4 |
| Propagation Delay | 8 ns |
| Turn On Delay Time | 25 ns |
| Logic Function | Multiplexer |
| Number of Inputs | 8 |
| Supply Type | Single |
| Bandwidth | 50MHz |
| Turn-Off Delay Time | 25 ns |
| On-State Resistance (Max) | 100Ohm |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 45 dB |
| Current - Leakage (IS(off)) (Max) | 1μA |
| On-state Resistance Match-Nom | 40Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 18ns, 18ns |
| Channel-to-Channel Matching (ΔRon) | 20 Ω (Max) |
| Crosstalk | -45dB @ 1MHz |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Signal Current-Max | 0.05A |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74LV4052ATPWRQ1 Overview
The electronic component is convenient to ship overseas because it is packed in a 16-TSSOP (0.173, 4.40mm Width). Advanced packaging method Tape & Reel (TR) is used to provide high reliability. It is mounted in the position Surface Mount. In the multiplexer and demultiplexer, 4:1 represents the number of circuits. The operating temperature is extended to around -40°C~105°C TA. A total of 16 terminations have been recorded. A 4 channel electronic part produces high-quality output. With a 3.3V voltage supply, the electrical component should be turned on and run. It is injected into the electrical part body with 16 pins. Circuits based on SP4T switching are used to construct these analog switch ics. The multiplexer consists of 2 circuits. Look for analog switch ic variants by searching with 74LV4052. This digital multiplexer has 100Ohm internal resistance. For functions related to 16 pins, please refer to the datasheets. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. Analogue multiplexer with a Single supply type that is cost-effective. 2V is the lowest voltage that should be fed to the electronic electronic part. This multiplexer would work with 20μA current. This analog switch requires a voltage of 2V~5.5V to drain from a single voltage supply. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. Operating 8 inputs is required. The data can be transferred over a wide range of bandwidths, called 50MHz bandwidths. 4-bits are supported. The series starts with Automotive, AEC-Q100.
SN74LV4052ATPWRQ1 Features
4 Channels
Switch Circuit: SP4T
20μA Supply Current
Bandwidth: 50MHz
4-Bit
SN74LV4052ATPWRQ1 Applications
There are a lot of Texas Instruments SN74LV4052ATPWRQ1 Analog Switches & Multiplexers ICs applications.
- RGB switches
- Video switching
- Low-Voltage
- DVD-R
- SDH/SONET multiplexers
- Medical Instrumentation
- Ultrasound
- PDAs
- Channelized and Unchannelized DS3 applications
- Residential Gateways, Home Gateway/Router
