SN74LV4066ADBRG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 14 |
| Weight | 121.789551mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 75Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 2.3V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74LV4066 |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Power Supplies | 2.5/5V |
| Number of Channels | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 20μA |
| Max Supply Current | 20μA |
| Throw Configuration | SPST |
| Propagation Delay | 10 ns |
| Turn On Delay Time | 25 ns |
| Input Voltage (Min) | 2V |
| Supply Type | Single |
| Bandwidth | 50MHz |
| Turn-Off Delay Time | 25 ns |
| On-State Resistance (Max) | 75Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 40 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 0.5pF 5.5pF |
| On-state Resistance Match-Nom | 6Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 12ns, 12ns |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -45dB @ 1MHz |
| Switching | MAKE-BEFORE-BREAK |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Normal Position | NO |
| Height | 2mm |
| Length | 6.2mm |
| Width | 5.3mm |
| Thickness | 1.95mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74LV4066ADBRG4 Overview
The electronic component is convenient to ship overseas because it is packed in a 14-SSOP (0.209, 5.30mm Width). To ensure high reliability, a new packaging method Tape & Reel (TR) is used. There is an analog multiplexer mounted in position Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Around -40°C~85°C TA is the extended operating temperature. In total, there have been 14 terminations. A electrical component with 4 channels is capable of high-quality output. It is safe to turn on and run the electronic component with a 2.3V voltage supply. An electrical component of this type can be found in the 14 series. Circuits based on SPST - NO switching are used to construct these analog switch ics. Try searching for 74LV4066 variants of the analog switch ic. The internal resistance of this digital multiplexer is 75Ohm. The datasheets for the 14 pins explain the functions. The analogue multiplexer in this example is a typical Multiplexer or Switches. A voltage higher than 5.5V should not normally be supplied to the switches. Analogue multiplexers of the Single supply type that are cost-effective. The lowest voltage the electronic part should receive is 2V. In order to operate this switch device, it would need a current of 20μA. Using only a single voltage supply, this analog switch requires 2V~5.5V voltage. When the digital multiplexer is charged above 20μA, damage can occur. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. This switch operates within the bandwidth of 50MHz.
SN74LV4066ADBRG4 Features
4 Channels
Switch Circuit: SPST - NO
20μA Supply Current
Bandwidth: 50MHz
SN74LV4066ADBRG4 Applications
There are a lot of Texas Instruments SN74LV4066ADBRG4 Analog Switches & Multiplexers ICs applications.
- FTTH
- Switching Systems
- Microprocessor Controlled Analog Systems
- High reliability control systems
- Mechanical reed relay replacement
- Modems
- PBX interfaces
- Audio/video switches
- HDTV
- SDH/SONET multiplexers
