Parameters |
Current - Leakage (IS(off)) (Max) |
100nA |
Channel Capacitance (CS(off), CD(off)) |
0.5pF 5.5pF |
On-state Resistance Match-Nom |
6Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
12ns, 12ns |
Channel-to-Channel Matching (ΔRon) |
2 Ω |
Crosstalk |
-45dB @ 1MHz |
Switching |
MAKE-BEFORE-BREAK |
Switch-on Time-Max |
25ns |
Switch-off Time-Max |
25ns |
Voltage - Supply, Single (V+) |
2V~5.5V |
Normal Position |
NO |
Height |
1.75mm |
Length |
8.65mm |
Width |
3.91mm |
Thickness |
1.58mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 1 day ago) |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
14-SOIC (0.154, 3.90mm Width) |
Number of Pins |
14 |
Weight |
129.387224mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Cut Tape (CT) |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
14 |
ECCN Code |
EAR99 |
Resistance |
75Ohm |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Subcategory |
Multiplexer or Switches |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
2.3V |
Terminal Pitch |
1.27mm |
Base Part Number |
74LV4066 |
Output |
SEPARATE OUTPUT |
Pin Count |
14 |
Polarity |
Non-Inverting |
Power Supplies |
2.5/5V |
Number of Channels |
4 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
2V |
Operating Supply Current |
20μA |
Nominal Supply Current |
20μA |
Max Supply Current |
20μA |
Throw Configuration |
SPST |
Propagation Delay |
10 ns |
Turn On Delay Time |
16 ns |
Input Voltage (Min) |
2V |
Supply Type |
Single |
Bandwidth |
50MHz |
Turn-Off Delay Time |
16 ns |
On-State Resistance (Max) |
75Ohm |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
40 dB |
SN74LV4066ADR Overview
The electronic part can be shipped overseas conveniently because it is packaged in 14-SOIC (0.154, 3.90mm Width). Advanced packaging method Cut Tape (CT) is used to provide high reliability. A switch device like this is mounted in Surface Mount. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operation at a temperature around -40°C~85°C TA. A total of 14 terminations have been recorded. The electronic part delivers high-quality output through its 4 channels. In the case of a voltage supply of 2.3V volts, the electrical part can be powered up and run. A total of 14 pins are injected into the body of the electronic part. On the other hand, analog switches can be constructed using SPST - NO switching circuits. Try searching with 74LV4066 if you're looking for variants. It has an internal resistance of 75Ohm. For functions related to 14 pins, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. The analog switch ic is of the Single supply type and is cost-effective. There should be 2V voltage fed to the electrical part below 2V. In order to operate this switch device, it would need a current of 20μA. A voltage of 2V~5.5V is required to drain this analog switch from a single voltage supply. If you put voltage higher than 20μA on the digital multiplexer, damage may occur. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. In 50MHz-bandwidths, data can be transferred.
SN74LV4066ADR Features
4 Channels
Switch Circuit: SPST - NO
20μA Supply Current
Bandwidth: 50MHz
SN74LV4066ADR Applications
There are a lot of Texas Instruments SN74LV4066ADR Analog Switches & Multiplexers ICs applications.
- SONET/SDH ADM
- Multiplexers
- Private Branch Exchange (PBX)
- USB 1.1 signal switching circuits
- Power routing
- SONET
- Cable Modem
- ATM
- Battery Powered Instruments
- Avionics test equipment