Parameters |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
14 |
Resistance |
75Ohm |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Subcategory |
Multiplexer or Switches |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
2.3V |
Base Part Number |
74LV4066 |
Output |
SEPARATE OUTPUT |
Pin Count |
14 |
Polarity |
Non-Inverting |
Power Supplies |
2.5/5V |
Number of Channels |
4 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
2V |
Operating Supply Current |
20μA |
Nominal Supply Current |
20μA |
Max Supply Current |
20μA |
Throw Configuration |
SPST |
Propagation Delay |
10 ns |
Turn On Delay Time |
16 ns |
Input Voltage (Min) |
2V |
Supply Type |
Single |
Bandwidth |
50MHz |
Turn-Off Delay Time |
16 ns |
On-State Resistance (Max) |
75Ohm |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
40 dB |
Current - Leakage (IS(off)) (Max) |
100nA |
Channel Capacitance (CS(off), CD(off)) |
0.5pF 5.5pF |
On-state Resistance Match-Nom |
6Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
12ns, 12ns |
Channel-to-Channel Matching (ΔRon) |
2 Ω |
Crosstalk |
-45dB @ 1MHz |
Switching |
MAKE-BEFORE-BREAK |
Switch-on Time-Max |
25ns |
Switch-off Time-Max |
25ns |
Voltage - Supply, Single (V+) |
2V~5.5V |
Normal Position |
NO |
Height |
1.2mm |
Length |
5mm |
Width |
4.4mm |
Thickness |
1mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 1 day ago) |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
14-TSSOP (0.173, 4.40mm Width) |
Number of Pins |
14 |
Weight |
57.209338mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
SN74LV4066APW Overview
Due to its 14-TSSOP (0.173, 4.40mm Width) packaging, the electronic part is convenient for international shipping. High reliability is achieved by using advanced packaging method Tube. A switch device like this is mounted in Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. Extended operating temperature around -40°C~85°C TA. 14 terminations have been made so far. By its 4 channels, the electronic component provides high-quality output. When a voltage supply of 2.3V is used, the electronic component should be turned on and run. A total of 14 pins are injected into the electrical part body. Circuits based on SPST - NO switching are used to construct these analog switch ics. Search with 74LV4066 if you are looking for analog multiplexer variants. This digital multiplexer has 75Ohm internal resistance. Please refer to the datasheets for 14 pins functions. Multiplexer or Switches is a typical switch device. normally, users should not supply switches with voltages higher than 5.5V. Single supply type digital switch with a low cost. 2V should be the lowest voltage fed to the electronic component. This digital switch can be operated with a current of 20μA. The voltage required by this switch device is 2V~5.5V, draining from a single voltage supply. A digital multiplexer may suffer damage if voltage is applied above 20μA. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. 50MHz-bandwidths can be used to transfer data between multiplexers.
SN74LV4066APW Features
4 Channels
Switch Circuit: SPST - NO
20μA Supply Current
Bandwidth: 50MHz
SN74LV4066APW Applications
There are a lot of Texas Instruments SN74LV4066APW Analog Switches & Multiplexers ICs applications.
- Cellular phones
- 65 V DACs
- High reliability control systems
- Sample-and-hold systems
- Optical Applications
- Intelligent PBX
- Remote wireless modules
- USB 1.1 signal switching circuits
- Access Concentrators
- Audio signal routing