Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 1 day ago) |
Contact Plating |
Gold |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
14-TSSOP (0.173, 4.40mm Width) |
Number of Pins |
14 |
Weight |
57.209338mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
14 |
ECCN Code |
EAR99 |
Resistance |
75Ohm |
Subcategory |
Multiplexer or Switches |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
2.3V |
Base Part Number |
74LV4066 |
Pin Count |
14 |
Polarity |
Non-Inverting |
Power Supplies |
2.5/5V |
Number of Channels |
4 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
2V |
Operating Supply Current |
20μA |
Nominal Supply Current |
20μA |
Max Supply Current |
20μA |
Throw Configuration |
SPST |
Propagation Delay |
10 ns |
Turn On Delay Time |
16 ns |
Input Voltage (Min) |
2V |
Supply Type |
Single |
Bandwidth |
50MHz |
Turn-Off Delay Time |
16 ns |
On-State Resistance (Max) |
75Ohm |
High Level Output Current |
25mA |
Low Level Output Current |
25mA |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
40 dB |
Current - Leakage (IS(off)) (Max) |
100nA |
Channel Capacitance (CS(off), CD(off)) |
0.5pF 5.5pF |
On-state Resistance Match-Nom |
6Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
12ns, 12ns |
Channel-to-Channel Matching (ΔRon) |
2 Ω |
Crosstalk |
-45dB @ 1MHz |
Switching |
MAKE-BEFORE-BREAK |
Switch-on Time-Max |
25ns |
Switch-off Time-Max |
25ns |
Voltage - Supply, Single (V+) |
2V~5.5V |
Drain to Source Resistance |
38Ohm |
Normal Position |
NO |
Height |
1.2mm |
Length |
5mm |
Width |
4.4mm |
Thickness |
1mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
SN74LV4066APWR Overview
This electronic part is conveniently packaged in 14-TSSOP (0.173, 4.40mm Width), making it easy to ship abroad. The advanced packaging method Tape & Reel (TR) provides high reliability. This analog switch is mounted in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Operational temperature extended around -40°C~85°C TA. Totally, there are 14 terminations. A 4 channel electronic part produces high-quality output. When a voltage supply of 2.3V is used, the electronic component should be turned on and run. An electrical component like this is included in the 14 series. These analog multiplexers are built based on SPST - NO switching circuits. Look for analog switch ic variants by searching with 74LV4066. Internally, this switch multiplexer has a resistance of 75Ohm. Please refer to the datasheets for 14 pins functions. In this analog multiplexer, the value is Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 5.5V to the switch device in normal circumstances. An effective Single supply digital multiplexer. 2V is the lowest voltage the electrical component should receive. It would be sufficient to run this analogue multiplexer with 20μA current. An analogue multiplexer drains from a single voltage supply at 2V~5.5V. It may damage the digital multiplexer if the voltage is higher than 20μA. In 50MHz-bandwidths, data can be transferred. There is 38Ohm resistance between Drain and Source for this electronic part.
SN74LV4066APWR Features
4 Channels
Switch Circuit: SPST - NO
20μA Supply Current
Bandwidth: 50MHz
Drain-to-Source resistance: 38Ohm
SN74LV4066APWR Applications
There are a lot of Texas Instruments SN74LV4066APWR Analog Switches & Multiplexers ICs applications.
- Signal routing between systems
- DSLAMs
- CSU
- Cross Connects
- Industrial and process control systems
- Cell phones
- FTTH
- Isolation
- Audio signal routing
- Switching Systems