SN74LV74AQPWRG4Q1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Weight | 57.209338mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | Automotive, AEC-Q100, 74LV |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 2V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 2.5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74LV74 |
| Function | Set(Preset) and Reset |
| Number of Outputs | 4 |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 3.3V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Clock Frequency | 140MHz |
| Propagation Delay | 20 ns |
| Turn On Delay Time | 9.8 ns |
| Family | LV/LV-A/LVX/H |
| Logic Function | AND, D-Type |
| Current - Quiescent (Iq) | 20μA |
| Current - Output High, Low | 12mA 12mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 9.3ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 2pF |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74LV74AQPWRG4Q1 Overview
In the form of 14-TSSOP (0.173, 4.40mm Width), it has been packaged. There is an embedded version in the package Tape & Reel (TR). As configured, the output uses Differential. The trigger it is configured with uses Positive Edge. The electronic part is mounted in the way of Surface Mount. It operates with a supply voltage of 2V~5.5V. In this case, the operating temperature is -40°C~125°C TA. A flip flop of this type is classified as a D-Type. JK flip flop is a part of the Automotive, AEC-Q100, 74LVseries of FPGAs. In order for it to function properly, its output frequency should not exceed 140MHz. This process consumes 20μA quiescents. There are 14 terminations,The 74LV74family includes it. Power is provided by a 2.5V supply. There is 2pF input capacitance for this T flip flop. This D flip flop belongs to the family of LV/LV-A/LVX/H. Electronic part Surface Mountis mounted in the way. This board has 14 pins. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. It is part of the FF/Latchesbase part number family. 5.5Vis the maximum supply voltage (Vsup). The supply voltage (Vsup) should be maintained above 2V for normal operation. Its superior flexibility is attributed to its use of 2 circuits. As a result of its reliable performance, this T flip flop is suitable for TR. A total of 3.3V power supplies are needed to run it. In order for the chip to function, it has 1output lines.
SN74LV74AQPWRG4Q1 Features
Tape & Reel (TR) package
Automotive, AEC-Q100, 74LV series
14 pins
3.3V power supplies
SN74LV74AQPWRG4Q1 Applications
There are a lot of Texas Instruments SN74LV74AQPWRG4Q1 Flip Flops applications.
- Storage registers
- 2 – Bit synchronous counter
- Registers
- Latch-up performance
- Count Modes
- Single Up Count-Control Line
- Shift Registers
- Buffer registers
- Computers
- CMOS Process
