Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 2 days ago) |
Contact Plating |
Gold |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
SOT-23-6 |
Number of Pins |
6 |
Weight |
6.492041mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Cut Tape (CT) |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
6 |
Termination |
SMD/SMT |
ECCN Code |
EAR99 |
Resistance |
15Ohm |
Subcategory |
Multiplexers or Switches |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
2.3V |
Terminal Pitch |
0.95mm |
Base Part Number |
74LVC1G3157 |
Pin Count |
6 |
Number of Outputs |
2 |
Polarity |
Non-Inverting |
Number of Channels |
1 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.65V |
Operating Supply Current |
1μA |
Nominal Supply Current |
10μA |
Max Supply Current |
10μA |
Propagation Delay |
300 ps |
Turn On Delay Time |
5.7 ns |
Supply Type |
Single |
Bandwidth |
300MHz |
Turn-Off Delay Time |
3.8 ns |
-3db Bandwidth |
340MHz |
On-State Resistance (Max) |
15Ohm |
High Level Output Current |
128mA |
Low Level Output Current |
128mA |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
57 dB |
Channel Capacitance (CS(off), CD(off)) |
5.2pF |
On-state Resistance Match-Nom |
0.1Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
5.7ns, 3.8ns |
Charge Injection |
7pC |
Channel-to-Channel Matching (ΔRon) |
100m Ω |
Crosstalk |
-54dB @ 10MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-off Time-Max |
7.5ns |
Voltage - Supply, Single (V+) |
1.65V~5.5V |
Drain to Source Resistance |
11Ohm |
Normal Position |
NC |
Height |
1.45mm |
Length |
2.9mm |
Width |
1.6mm |
Thickness |
1.2mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
SN74LVC1G3157DBVR Overview
Shipping overseas is convenient with the electronic component packed in SOT-23-6. To ensure high reliability, a new packaging method Cut Tape (CT) is used. Surface Mount is where this multiplexer is located. 2:1 is the number of circuits in the multiplexer and demultiplexer. Operation at a temperature around -40°C~85°C TA. A total of 6 terminations have been recorded. As a result of its 1 channels, this electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 2.3V voltage supply. This electronic part can be found in the 6 series. Circuits based on SPDT switching are used to construct these analog switch ics. Try searching for the analog switch ic with 74LVC1G3157 if you are looking for variants. As far as internal resistance is concerned, it has 15Ohm. The datasheets for the 6 pins explain the functions. Theswitch device is a typical Multiplexers or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. A analog switch ic that has a cost-effective Single supply type. A low voltage of 1.65V should be applied to the electronic component. 1μA current would be enough for this multiplexer to operate. A voltage of 1.65V~5.5V is required to drain this analog switch from a single voltage supply. A voltage higher than 10μA may cause damage to the switch multiplexer. In 300MHz-bandwidths, data can be transferred. There is 11Ohm resistance between Drain and Source for this electronic part. This digital multiplexer has 2 outputs.
SN74LVC1G3157DBVR Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
-3db Bandwidth: 340MHz
Bandwidth: 300MHz
Drain-to-Source resistance: 11Ohm
SN74LVC1G3157DBVR Applications
There are a lot of Texas Instruments SN74LVC1G3157DBVR Analog Switches & Multiplexers ICs applications.
- PBX interfaces
- Industrial
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Industrial and process control systems
- Medical
- Data switching
- Digital cross connects (DSX-1)
- Access Concentrators
- Microprocessor controlled systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)